Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SYSTEM SETTING PANEL SECTION
@ 45/9-pin remote control system select switches
Select the remote contro! systems depending on the types
of VTRs connected.
45:
for VTRs with a 45-pin remote control interface
9:
for VTRs with a 9-pin remote control interface
@ TC/CTL select switches
CTL:
Counts and indicates the CTL signals recorded
on the tape. The counter display can be reset
by pressing the RESET button.
TC:
Indicates the time codes read by the 9-pin
remote control system. The time code display
cannot be reset by pressing the RESET button.
@® SYSTEM BUMP ON/OFF switch
ON:
Capstan bump function controls tape running
for highly accurate editing.
OFF:
No capstan bump function.
With the BUMP switch ON, the three VTRs run in
phase.
@ SYSTEM PREROLL time select switch
Preroll times of 5 seconds, 7 seconds and 10 seconds can
be selected. Preroll time of 10 seconds can be changed to
15 seconds by setting DIP switch SW1-5 @ to ON. The
capstan bump function does not operate with preroll time of
5 seconds.
NOTE:
@ When using the SA-F911E Interface Unit, set the preroll
time to 10 seconds or longer.
@ System setup DIP switches
To change the factory preset functions of the editing
system.
Prior to shipment, all switches are set to OFF
(down).
Selects
the
automatic
retry mode
when
in-phase
adjustment fails with the BUMP switch ON: whether the
retries should be performed with changing preroll times or
changing editing accuracy.
Swt-1
With changing preroll times
OFF
When set to 7 sec: 7
72 7= 10-10
10
When set to 10 sec: 10 = 10 = 10
When set to 15 sec: 15> 15
15
With changing editing accuracy
ON
4-Field CF mode: 0 frame = +1 frame = Rough
8-Field CF mode: 0 frame = +2 frames => Rough
OUT point return function ON/OFF switch in insert editing.
W1-2
OUT point return function ON
OFF
OUT point return function OFF
ON
Auto REC EE function ON/OFF switch (With auto REC EE
function ON, the REC EE mode is automatically cancelled
when the recorder is operated manually with the REC EE
switch set to ON, or the REC EE mode is automatically
engaged when either player is operated.)
Swi-3
Auto REC EE function OFF OFF
Auto REC EE function ON
ON
-1li-
No.
Function
SW1-4 | Not used. Keep set to OFF.
Switches the 10-second preroll time to 15 seconds.
SW1-5
10 seconds
OFF
15 seconds
ON
To select edit-in timing in 9-pin editing. It is preset to —-3
frames.
Swi-5
Swi-6
SW1-7
SW1-8
—1 frame
OFF
ON
OFF
SW1-6
—2 frames
OFF
OFF
ON
SW1-7
-3 frames
OFF
OFF
OFF
—4 frames
OFF
ON
ON
—5 frames
ON
OFF
OFF
-6 frames
ON
OFF
ON
-7 frames
ON
OFF
—8 frames
ON
ON
Time counter memory/Special function select switch.
sWwe-1
Time counter memory
OFF
Special function
ON
To select editing accuracy. Set to "+1 frame" when the
4-field colour framing mode is selected with the KR-M840E
connected.
SWwe-3
SWe-2
SW2-3
0 frame
OFF
OFF
+1 frame
OFF
ON
+2 frames
ON
OFF
ON
ON
Determines whether or not there will be a beep when a
control button is pressed.
SWe-4
Beep
OFF
No beep
ON
To select the colour framing mode
(effective in 9-pin
editing).
Rough
SWe2-5
2-field mode
ON
4-field or 8-field mode
OFF
To select the same-duration edit function (in which the
OUT point is automatically registered as the IN point of a
new edit and the OUT point of a new edit is also
automatically registered with respect to that IN point so
that the duration is the same as that of the previous edit.)
SW2-6
Same-duration edit function OFF
OFF
Same-duration edit function ON
ON
To select use of TBC when editing via the SA-F911E.
SWe-7
With TBC
ON
Without TBC
OFF
To defeat the auto colour frame shift function in 9-pin
timecode-referenced editing
SW2-8
Auto colour frame shift ON
ON
Auto colour frame shift OFF
OFF
Werbung
