Rohde & Schwarz R&S FSQ Bedienhandbuch Seite 795

R&S FSQ
Unterschiede im GPIB-Verhalten zwischen der R&S FSP- und R&S FSE-Gerätefamilie
Gerät Befehl (Sheet 38 of 50)
FSE [SENSe<1|2>:]FILTer:HPASs:FREQuency
FSET [SENSe<1|2>:]FILTer:HPASs:FREQuency
FSE [SENSe<1|2>:]FILTer:HPASs[:STATe]
FSE [SENSe<1|2>:]FILTer:LPASs:FREQuency
FSE [SENSe<1|2>:]FILTer:LPASs[:STATe]
FSET [SENSe<1|2>:]FILTer:NOTCh[:STATe]
FSET [SENSe<1|2>:]FM[:DEViation]:RANGe:UPPer
FSET [SENSe<1|2>:]FM[:DEViation]:RANGe[:UPPer]
R&S FSE [SENSe<1|2>:]FREQuency:CENTer
FSQ
FSE [SENSe<1|2>:]FREQuency:CENTer:LINK
R&S FSE [SENSe<1|2>:]FREQuency:CENTer:STEP
FSQ
R&S FSE [SENSe<1|2>:]FREQuency:CENTer:STEP:LINK
FSQ
R&S FSE [SENSe<1|2>:]FREQuency:CENTer:STEP:LINK:
FSQ FACTor
R&S FSE [SENSe<1|2>:]FREQuency:MODE
FSQ
R&S FSE [SENSe<1|2>:]FREQuency:OFFset
FSQ
FSET [SENSe<1|2>:]FREQuency:RANGe
R&S FSE [SENSe<1|2>:]FREQuency:SPAN
FSQ
R&S FSE [SENSe<1|2>:]FREQuency:SPAN:FULL
FSQ
FSE [SENSe<1|2>:]FREQuency:SPAN:LINK
R&S FSE [SENSe<1|2>:]FREQuency:STARt
FSQ
6.350
Fernsteuerung – Beschreibung der Befehle
Parameter Hinweise
30 Hz | 300 HZ not available for
R&S FSQ and
R&S FSET
10 kHz | 1 kHz | 100 Hz not available for
R&S FSQ
ON | OFF not available for
R&S FSQ
3 kHz| 15 kHz not available for
R&S FSQ and
R&S FSET
ON | OFF not available for
R&S FSQ and
R&S FSET
ON | OFF not available for
R&S FSQ
ON | OFF not available for
R&S FSQ
<numeric_value> not available for
R&S FSQ
0 to f frequency ranges are
max
different for R&S FSQ
and R&S FSE
STARt | STOP | SPAN not available for
R&S FSQ
0 to f frequency ranges are
max
different for R&S FSQ
and R&S FSE
SPAN | RBW | OFF
1 to 100 PCT
CW|FIXed | SWEep
<numeric_value>
2 GHz | 22 GHz not available for
R&S FSQ
0 to f frequency ranges are
max
different for R&S FSQ
and R&S FSE
CENTer | STOP | SPAN not available for
R&S FSQ
0 to f frequency ranges are
max
different for R&S FSQ
and R&S FSE
Operating Manual 1313.9681.11 - 02