Kärcher GSH 4-4 Plus Bedienungsanleitung Seite 23

Store the device in a dry and well-ventilated interior
space.
Do not expose the device to direct sunlight for a long
time.
Keep the device away from corrosive substances such
as garden chemicals and de-icing salts.
5. Store the device in a dry, well ventilated interior
space.
Care and maintenance
DANGER
Risk of injury due to cuts from sharp blades and ac-
cidentally switching on the device!
Remove the battery from the device before all work on
the device.
Make sure that the ON/OFF button is not pressed while
inserting the battery pack.
Avoid unintentionally switching on the device.
Wear safety goggles and protective gloves when work-
ing on the device.
Always mount the blade guard before working on the
device and before transporting it.
Cleaning the device
ATTENTION
Risk of damage due to incorrect cleaning!
Only clean the device with a hand-held brush and damp
cloth.
Do not use solvent-based cleaning agents.
Do not immerse the device in water or other liquids.
Do not clean the device with a hose or high-pressure
water jet.
1. Release the ON/OFF button.
The device switches off.
2. Remove the battery pack from the device, see chap-
ter Removing the battery pack.
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device is not work-
ing.
The device stops during
operation
Charge indicator Error description
An LED flashes slowly The battery pack is fully discharged. 1
and the motor is off.
Troubleshooting guide
Cause
The battery pack is not sitting properly in
the device.
The charging state of the battery pack is
too low.
The battery pack is overheated.
The battery pack or charger is defective. 1. Replace the battery pack or charger, see
Motor has overheated
Error codes and error descriptions
3. Remove cuttings with a hand-held brush.
Illustration T
4. Remove resin from the blades, e.g. with the Kärcher
Universal Stain Remover RM 769.
5. Oil the blades of the grass or shrub shears, see
chapter Oiling the blades.
6. Mount the blade guard, see chapter Mounting the
blade guard.
7. Clean the device with a damp cloth if required.
8. Remove dirt and foreign objects from the battery
pack holder with a damp cloth.
Note
Clean the optionally available telescoping handle in the
same way.
Note
To maintain blade quality and optimum cutting results,
apply a little spray oil or thin machine oil to the blades of
the grass and shrub shears after each use.
1. Release the ON/OFF button.
The device switches off.
2. Remove the battery pack from the device, see chap-
ter Removing the battery pack.
3. Clean the device, see chapter Cleaning the device.
4. Place the device on a horizontal, level and oil-resist-
ant surface.
Illustration U
5. Apply a thin layer of oil to the top of the blades of the
grass and shrub shears.
6. Mount the blade guard, see chapter Mounting the
blade guard.
7. Clean the base and dispose of oil residues in an en-
vironmentally friendly manner and in accordance
with local regulations.
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
1. Push the battery pack into the battery
mount on the device until it you feel it latch
into place.
1. Charge the battery pack, see chapter Bat-
tery pack charging.
1. Take the battery pack out of the device and
let it cool down, see chapter Removing the
battery pack.
Note
The battery pack can get very warm.
2. Do not the place the device and battery
pack in direct sunlight.
chapter Intended use.
1. Stop working and allow the motor to cool
down.
Error correction
Charge the battery pack or replace it with a charged
battery pack, see chapter Battery pack charging.
English
Oiling the blades
23