Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• Check the device and accessory parts for transport damage.
In the event of complaints the carrier must be informed im-
mediately. Later claims will not be recognised.
• Familiarise yourself with the product by means of the operat-
ing instructions before using for the first time.
• With accessories as well as wearing parts and replacement
parts use only original parts. Replacement parts can be ob-
tained from your dealer.
• When ordering please provide our article number as well as
type and year of manufacture for your equipment.
m Attention!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!
9. Assembly
m WARNING!
Risk of injury and damage!
The use of incorrect spare parts and accessories can lead to
injuries and damage. These could come loose and be flung
away. They can also reduce the power of the product.
- Only use original spare parts and accessories from the
manufacturer. Original spare parts or accessories can be
obtained from your dealer.
- Failure to do so may reduce the power of the product and
parts may come loose.
- Failure to observe this will invalidate the manufacturer's
warranty.
NOTE!
Due to the heavy weight of the product, we recom-
mend installation by at least two people.
Some parts of the mower come disassembled. You require the
following for assembly:
• Open-end spanner AF 12 mm (installation of gear selector
lever)
• Open-end spanner AF 13 mm (installation of gear selector
lever)
• Open-end spanner AF 16 mm (assembly of frame)
• Open-end spanner AF 17 mm (assembly of frame)
• Open-end spanner AF 19 mm (assembly of wheels)
The assembly tool is not included in the scope of delivery.
9.1 Installing the frame (21) (Fig. 3)
1. Align the holes of the frame (21) with the holes of the side
parts of the frame.
2. Secure the frame (21) with the screws (enclosed acces-
sories bag A M10x45mm and B M10x25), washers and
nuts.
9.2 Fitting the wheels (8) (Fig. 4)
1. Push the wheels (8) onto the wheel screws and fasten them
with the included washers and lock nuts (C, M12).
2. Make sure that the valve (which is needed to inflate the
wheels) is on the outer side of each wheel (8).
3. Also pay attention to the direction arrow on the wheel.
9.3 Installing the gear selector lever (14) (Fig. 5)
1. Remove the pre-assembled screws from the gear selector
lever (14).
2. Slide the gear selector lever (14) through the slot of the
switch plate (13).
3. Fasten the gear selector lever (14) on the inside of the
switch bracket (10) using the screws M8x30mm. Make
sure that the labelling of the gear selector lever (14) points
towards the user.
9.4 Fitting the transport tray (4) (Fig. 6)
1. Push the transport tray (4) laterally into the guide pins pro-
vided for this purpose on the frame.
2. Secure the transport tray (4) using the enclosed cotter pins
(D).
9.5 On/Off switch cable (26) (Fig. 7)
1. Fasten the on/off switch cable (26) using the included ca-
ble connectors.
10. Before commissioning
m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
m WARNING!
Risk to health!
Inhalation of petrol/lubricating oil vapours and exhaust gases
can cause serious damage to health, unconsciousness and in
extreme cases death.
- Do not breathe petrol/lubricating oil vapours and exhaust
gases.
- Only use the product outdoors.
NOTE!
Product damage
Using the product without or with too little engine and gear oil
can result in engine damage.
- Fill with petrol and oil before commissioning. The product is
supplied without engine oil.
NOTE!
Environmental damage!
Spilled oil can pollute the environment permanently. The liquid
is highly toxic and can quickly lead to water pollution.
- Fill/empty oil only on level, paved surfaces.
- Use a filling nozzle or funnel.
- Collect drained oil in a suitable container.
- Immediately wipe up any spilled oil carefully and dispose it
according to local regulations.
- Dispose of oil as per local regulations.
NOTE!
Risk of damage!
If incorrectly stored or undrained fuel is used, the carburettor
may become clogged or engine operation may be affected.
- Put unused fuel in an airtight vessel and store it in a dark,
cool room.
GB/IE
9
Werbung
