Siemens SINUMERIK 840D sl Programmierhandbuch Seite 15

18 Eigene Abspanprogramme.......................................................................................................................595
18.1 Unterstützende Funktionen für das Abspanen.....................................................................595
18.2 Konturtabelle erstellen (CONTPRON).................................................................................595
18.3 Codierte Konturtabelle erstellen (CONTDCON)...................................................................601
18.4 Schnittpunkt zwischen zwei Konturelementen ermitteln (INTERSEC).................................605
18.5 Konturelemente einer Tabelle satzweise abfahren (EXECTAB)..........................................606
18.6 Kreisdaten berechnen (CALCDAT)......................................................................................607
18.7 Konturaufbereitung ausschalten (EXECUTE)......................................................................609
19 Zyklen extern programmieren...................................................................................................................611
19.1 Technologische Zyklen........................................................................................................611
19.1.1 Einleitung.............................................................................................................................611
19.1.2 Technologie-spezifische Übersicht......................................................................................612
19.1.3 HOLES1 - Lochreihe............................................................................................................614
19.1.4 HOLES2 - Lochkreis............................................................................................................614
19.1.5 POCKET3 - Rechtecktasche fräsen.....................................................................................616
19.1.6 POCKET4 - Kreistasche fräsen...........................................................................................619
19.1.7 SLOT1 - Längsnut................................................................................................................621
19.1.8 SLOT2 - Kreisnut.................................................................................................................624
19.1.9 LONGHOLE - Langloch.......................................................................................................626
19.1.10 CYCLE60 - Gravurzyklus.....................................................................................................628
19.1.11 CYCLE61 - Planfräsen.........................................................................................................631
19.1.12 CYCLE62 - Konturaufruf......................................................................................................633
19.1.13 CYCLE63 - Konturtasche fräsen..........................................................................................634
19.1.14 CYCLE64 - Konturtasche vorbohren....................................................................................636
19.1.15 CYCLE70 - Gewindefräsen..................................................................................................637
19.1.16 CYCLE72 - Bahnfräsen........................................................................................................639
19.1.17 CYCLE76 - Rechteckzapfen fräsen.....................................................................................643
19.1.18 CYCLE77 - Kreiszapfen fräsen............................................................................................645
19.1.19 CYCLE78 - Bohrgewinde fräsen..........................................................................................647
19.1.20 CYCLE79 - Mehrkant...........................................................................................................649
19.1.21 CYCLE81 - Bohren, Zentrieren............................................................................................651
19.1.22 CYCLE82 - Bohren, Plansenken..........................................................................................652
19.1.23 CYCLE83 - Tieflochbohren..................................................................................................655
19.1.24 CYCLE84 - Gewindebohren ohne Ausgleichsfutter.............................................................658
19.1.25 CYCLE85 - Reiben...............................................................................................................661
19.1.26 CYCLE86 - Ausdrehen.........................................................................................................662
19.1.27 CYCLE92 - Abstich..............................................................................................................663
19.1.28 CYCLE95 - Konturabspanen................................................................................................665
19.1.29 CYCLE98 - Gewindekette....................................................................................................667
19.1.30 CYCLE99 - Gewindedrehen.................................................................................................671
19.1.31 CYCLE435 - Abrichterposition berechnen...........................................................................676
19.1.32 CYCLE495 - Profilieren........................................................................................................676
19.1.33 CYCLE800 - Schwenken.....................................................................................................678
19.1.34 CYCLE801 - Gitter oder Rahmen........................................................................................681
19.1.35 CYCLE802 - Beliebige Positionen.......................................................................................683
19.1.36 CYCLE830 - Tieflochbohren 2.............................................................................................686
19.1.37 CYCLE832 - High Speed Settings.......................................................................................692
Arbeitsvorbereitung
Programmierhandbuch, 10/2015, 6FC5398-2BP40-5AA3
Inhaltsverzeichnis
15