Operating The Trimmer; Cutting Tips - Ryobi RLT30CET Bedienungsanleitung

EN
FR DE ES
refueling or maintenance of the product is taking
place.
Charge battery pack only with the charger assembly
Q
provided (BPH-1215 / 12V Ni-Cd).
Make sure power supply is normal household voltage,
Q
230V/ 240V~, 50 Hz.
Connect charger to power supply.
Q
Place battery pack in charging stand. Align raised rib
Q
on battery pack with groove in charging stand. (See
Figure 8.)
Press down on battery pack to be sure contacts
Q
on battery pack engage properly with contacts in
charging stand.
The charge indicator light (LED), located on the
Q
charging stand, will light up red when the charger
is properly connected to power supply. This light
indicates the charger is operating properly. It will
remain on until battery pack is removed from charging
stand or charger is disconnected from power supply.
After normal usage, 3 hours or less of charging time is
Q
required to fully recharge battery pack.
If both red and orange LED indicators glow, the
Q
battery pack is deeply or completely discharged, and
6 hours or longer of charging time is required to fully
recharge battery pack.
NOTE: If charger does not charge battery pack
or orange LED continues to glow after more than 30
minutes of charging, return battery pack and charging
assembly to your nearest Ryobi Authorised Service
Centre for electrical check.
The battery pack will become slightly warm to the
Q
touch while charging. This is normal and does not
indicate a problem.
Do not place charger in an area of extreme heat or
Q
cold. It will work best at normal room temperature.
When batteries become fully charged, unplug charger
Q
from power supply and remove the battery pack.

OPERATING THE TRIMMER

See Figure 9.
WARNING:
Always position the unit on the operator's right
side. The use of the unit on the operator's left
side will expose the user to hot surfaces and can
result in possible burn injury.
WARNING:
To avoid burns from hot surfaces, never operate
unit with the bottom of the engine above waist
level.
Hold the trimmer with your right hand on the rear handle
and your left hand on the front handle. Keep a firm grip
IT PT NL SV DA
English (original instructions)
NO FI HU CS RU
with both hands while in operation. Trimmer should be
held at a comfortable position with the rear handle about
hip height.
Always operate trimmer at full throttle. Cut tall grass from
the top down. This will prevent grass from wrapping
around the shaft housing and string head which could
cause damage from overheating. If grass becomes
wrapped around the string head, STOP THE ENGINE,
disconnect the spark plug lead, and remove the grass.
Prolonged cutting at partial throttle will result in lubricant
dripping from the muffler.
TO ADVANCE THE CUTTING LINE
(Reel Easy line trimer head)
Line advance is controlled by tapping the string head on
grass while running engine at full throttle.
Run engine at full throttle.
Q
Tap the knob on ground to advance string. The string
Q
advances each time the knob is tapped. Do not hold
the knob on the ground.
NOTE: The line trimming cut-off blade on the grass
deflector will cut the line to the correct length.
NOTE: If the string is worn too short you may not be able
to advance the string by tapping it on the ground. If so,
stop the engine, and manually advance the string.
TO ADVANCE THE CUTTING LINE MANUALLY:
Stop the engine and disconnect the spark plug lead.
Q
Push the knob in while pulling on string(s) to manually
Q
advance the line.
NOTE: Pro Cut II line cannot be advanced. To replace
the line, refer to Installing Line in Pro Cut II Line Trimmer
Head later in this manual.

CUTTING TIPS

See Figures 9 - 11.
Avoid hot surfaces by always keeping the tool away
Q
from your body. (Proper operating position shown in
figure 9.)
Keep the trimmer tilted toward the area being cut; this
Q
is the best cutting area.
The trimmer cuts when passing the unit from left to
Q
right. This will avoid throwing debris at the operator.
Avoid cutting in the dangerous area shown in
illustration.
Use the tip of string to do the cutting; do not force
Q
string head into uncut grass.
Wire and picket fences cause extra line wear, even
Q
breakage. Stone and brick walls, curbs, and wood
may wear line rapidly.
Avoid trees and shrubs. Tree bark, wood mouldings,
Q
siding, and fence posts can easily be damaged by the
string.
22
RO PL SL HR ET LT LV SK BG