Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
●
before leaving the product unattended
●
before checking for damage after striking a foreign
object
●
before performing maintenance
●
whenever the product starts to vibrate abnormally
■
Do not force the product through heavy shrubbery. This
can cause the blades to bind and slow down. If the
blades slow down, reduce the pace.
■
If the product is dropped, suffers heavy impact, or begins
to vibrate abnormally, immediately turn off the product
and inspect it for damage or identify the cause of the
vibration. Any damage should be properly repaired or
replaced by an authorised service centre.
■
Do not wear multiple belt or shoulder harnesses.
■
Operate the product only in temperatures between 0°C
and 40°C.
■
Store the product in a location where the ambient
temperature is between 0°C and 40°C.
■
Injuries may be caused, or aggravated, by prolonged use
of the product. When using any product for prolonged
periods, ensure to take regular breaks.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse the tool,
battery pack, or charger in fluid or allow fluid to flow inside
them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
■
Charge the battery pack in a location where the ambient
temperature is between 10°C and 38°C.
■
Store the battery pack in a location where the ambient
temperature is between 0°C and 40°C.
■
Use the battery pack in a location where the ambient
temperature is between 0°C and 40°C.
TRANSPORTATION AND STORAGE
■
Turn off the product, remove the battery pack, and allow
both to cool down before storing or transporting.
■
Remove all foreign materials from the product. Store the
product in a cool, dry, and well-ventilated area that is
inaccessible to children. For extra safety, store the battery
pack separately from the product. Keep the product away
from corrosive agents, such as garden chemicals and de-
icing salts. Do not store the product outdoors.
■
Fit the blade cover before storing the product or during
transportation.
■
For transportation, secure the product against movement
or falling to prevent injury to persons or damage to the
product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
MAINTENANCE
■
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
■
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only.
■
The blades are extremely sharp. To prevent personal
injury, exercise extreme caution when cleaning,
lubricating, fitting, or removing the blade cover.
■
Remove the battery pack before adjusting, maintaining,
or cleaning the product.
■
You may make adjustments and repairs described in this
manual. For other repairs, have the product serviced by
an authorised service centre only.
■
After each use, clean the plastic parts with a soft, dry cloth.
■
After each use, clean the debris from the blades with a
stiff brush, and then carefully apply a rust preventative
lubricant before refitting the blade protector. The
manufacturer recommends using rust preventative
lubricant spray to apply an even distribution and reduce
the risk of personal injury from contact with the blades.
For information about a suitable spray product, check
with an authorised service centre.
■
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure that the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
KNOW YOUR PRODUCT
See page 106.
1. Trigger release
2. On/Off trigger
3. Front hand grip
4. Harness hanger
5. Shaft coupling
6. Extension pole
7. Harness
8. Blade cover
9. Pivoting button
10. Blade
11. HEDGESWEEP debris sweeper
12. Operator's manual
13. Battery pack
14. Charger
SYMBOLS ON THE PRODUCT
Safety alert
Read and understand all instructions
before operating the product. Follow all
warnings and safety instructions.
Wear eye, ear, and head protection.
Wear non-slip safety footwear when
using the product.
5
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
Werbung
Inhaltsverzeichnis
