WAGO 750 XTR Handbuch Seite 8

8 Inhaltsverzeichnis
10.1.3.4.3.25
10.1.3.4.3.26
10.1.3.4.3.27
10.1.3.4.3.28
10.1.3.4.4
10.1.3.4.4.1
10.1.3.4.4.2
10.1.3.4.4.3
10.1.3.4.4.4
10.1.3.4.4.5
10.1.3.4.4.6
10.1.3.4.4.7
10.1.3.4.4.8
10.1.3.4.4.9
10.1.3.4.4.10
10.1.3.4.4.11
10.1.3.4.4.12
10.1.3.4.4.13
10.1.3.4.4.14
10.1.3.4.4.15
10.1.3.4.4.16
10.1.3.4.4.17
10.1.3.4.4.18
10.1.3.4.4.19
10.1.3.4.4.20
10.1.3.4.4.21
10.1.3.4.4.22
10.1.3.4.5
10.1.3.4.5.1
10.1.3.4.5.2
10.1.3.4.5.3
10.1.3.4.5.4
10.1.3.4.5.5
Handbuch
Version 1.3.0
750-838/040-000 Controller CANopen M3 DSub XTR
Objekt 0x5001 - Ausgangsprozessabbild schreiben ........ 182
Objekt 0x5200 - Feldbuskoppler-/
-controller-Konfiguration ................................................... 183
Objekt 0x5201 - Diagnosekonfiguration ........................... 186
Objekt 0x5202 - Modulkonfiguration ................................ 186
Standard Device Profile Area - DS 401 ................................ 189
Objekt 0x6000 - Read digital input 8-bit ........................... 191
Objekt 0x6005 - Global interrupt enable
digital 8-Bit ....................................................................... 191
Objekt 0x6006 - Digital interrupt mask any
change 8-Bit ..................................................................... 191
Objekt 0x6007 - Digital interrupt mask
low-to-high 8-Bit ............................................................... 192
Objekt 0x6008 - Digital interrupt mask
high-to-low 8-Bit ............................................................... 192
Objekt 0x6100 - Read digital input 16-bit ......................... 193
Objekt 0x6200 - Write digital output 8-bit ......................... 193
Objekt 0x6206 - Error mode digital output 8-bit ................ 194
Object 0x6207 - Error value digital output 8-Bit ................ 194
Objekt 0x6300 - Write digital output 16-Bit ....................... 195
Objekt 0x6401 - Read analog input 16-bit ........................ 195
Objekt 0x6411 - Write analog output 16-bit ...................... 196
Objekt 0x6421 - Analog input interrupt
trigger selection ................................................................ 196
Objekt 0x6423 - Analog input global
interrupt enable ................................................................ 196
Objekt 0x6424 - Analog input interrupt
upper limit integer ............................................................. 197
Objekt 0x6425 - Analog input interrupt
lower limit integer ............................................................. 197
Objekt 0x6426 - Analog input interrupt
delta unsigned .................................................................. 198
Objekt 0x6427 - Analog input interrupt
negative delta unsigned .................................................... 198
Objekt 0x6428 - Analog input interrupt
positive delta unsigned ..................................................... 199
Objekt 0x6443 - Analog output error mode ...................... 200
Objekt 0x6444 - Analog output error value integer ........... 200
Objekt 0x67FE - Error behaviour ..................................... 201
Reservierter Bereich ............................................................. 202
Objekt 0xA000,
Integer8-IEC-61131-1-Eingangsvariablen ........................ 204
Objekt 0xA040,
Unsigned8-IEC-61131-1-Eingangsvariablen ..................... 204
Objekt 0xA080,
Boolsche-IEC-61131-1-Eingangsvariablen ....................... 205
Objekt 0xA0C0,
Integer16-IEC-61131-1-Eingangsvariablen ....................... 205
Objekt 0xA101 bis 0xA8C0
IEC-61131-1-Ein- und Ausgangsvariablen........................ 205
WAGO I/O SYSTEM 750 XTR