Siemens SINAMICS S120 Handbuch Seite 660

Index
PROG_TEST_MASK
Programmbeeinflussungs-Signale von HMI
564
PROTAREA_GEOAX_CHANGE_MODE
PROTOC_IPOCYCLE_CONTROL
PROTOC_PREPTIME_CONTROL
PUNCH_DWELLTIME
PUNCH_PARTITION_TYPE
PUNCH_PATH_SPLITTING
PUNCHNIB_ACTIVATION
PUNCHNIB_ASSIGN_FASTIN
PUNCHNIB_ASSIGN_FASTOUT
PUNCHNIB_AXIS_MASK
R
RADIUS_NAME
RATED_OUTVAL
RATED_VELO
REBOOT_DELAY_TIME
REFP_CAM_DIR_IS_MINUS
REFP_CAM_IS_ACTIVE
REFP_CAM_MARKER_DIST
REFP_CAM_SHIFT
REFP_CYCLE_NR
REFP_MAX_CAM_DIST
REFP_MAX_MARKER_DIST
REFP_MOVE_DIST
REFP_MOVE_DIST_CORR
660
MD 10707 , 83
,
MD 10618 76
MD 11297 , 118
MD 11298 , 118
MD 42400 , 490
MD 26016 , 338
MD 26014 , 338
MD 26012 , 337
MD 26000 , 333
,
MD 26002 334
MD 26010 , 337
MD 10654 , 77
MD 32250 , 388
MD 32260 , 389
,
MD 10088 39
MD 34010 , 413
MD 34000 , 413
,
MD 34093 418
MD 34092 , 417
MD 34110 , 419
MD 34030 , 414
MD 34060 , 416
MD 34080 , 416
MD 34090 , 417
REFP_NC_START_LOCK
, MD 20700 , 251
REFP_PERMITTED_IN_FOLLOWUP
MD 34104 , 419
REFP_SEARCH_MARKER_REVERSE
MD 34050 , 415
REFP_SET_POS
MD 34100 , 418
REFP_STOP_AT_ABS_MARKER
,
MD 34330 424
REFP_SYNC_ENCS
MD 34102 , 419
REFP_VELO_POS
MD 34070 , 416
REFP_VELO_SEARCH_CAM
MD 34020 , 413
REFP_VELO_SEARCH_MARKER
MD 34040 , 414
REORG_LOG_LIMIT
MD 27900 , 346
REPOS_MODE_MASK
MD 11470 , 131
RESET_MODE_MASK
MD 20110 , 213
ROT_IS_MODULO
MD 30310 , 367
RUN_OVERRIDE_0
MD 12200 , 144
S
S_VALUES_ACTIVE_AFTER_RESET
MD 22400 , 273
SCALING_FACTOR_G70_G71
MD 31200 , 378
SCALING_FACTORS_USER_DEF
MD 10230 , 47
SCALING_SYSTEM_IS_METRIC
MD 10240 , 48
SCALING_USER_DEF_MASK
MD 10220 , 45
SCALING_VALUE_INCH
MD 10250 , 49
SD_MAX_PATH_ACCEL
,
MD 42500 496
SD_MAX_PATH_JERK
MD 42510 , 497
SEARCH_RUN_MODE
MD 11450 , 129
SERUPRO_MASK
MD 10708 ,
83
Maschinendaten und Nahtstellensignale
Listenhandbuch, 03/2011, 6FC5397-5CP10-3AA0