Servicing The Fluid Section - WAGNER LineCoat 820 Betriebsanleitung

LineCoat 840 and LineCoat 860
1
2
Motor/
Pump
Block
3
4
5
Item Part # Description
1 0349406 Retaining ring ...........................................1
2 0349407 Connecting pin .........................................1
3 0349408 O-ring, Teflon............................................2
4 0349409 Packing set, leather/UHMWPE/steel........2
5 0349410 Upper packing spring ...............................1
6 0349596 Displacement rod, LC 840 .........................1
0555682 Displacement rod, LC 860
7 0349412 Spring retainer..........................................1
8 0349413 Lower packing spring ...............................1
9 0349622 Outlet valve cage .....................................1
10 0349414 Outlet valve ball........................................1
11 0555668 Outlet valve seat ......................................1
12 0555669 Seal washer..............................................1
13 0555670 Outlet valve housing.................................1
14 0555671 Pump cylinder, LC 840 .............................1
0555681 Pump cylinder, LC 860
15 0349417 O-ring .......................................................1
16 0528081 Wave washer............................................1
17 0555672 Foot valve cage........................................1
18 0349477 Foot valve ball ..........................................1
19 0555673 Foot valve seat.........................................1
20 0555674 Seat o-ring................................................1
21 0555675 Foot valve housing ...................................1
0555676 Fluid section service kit, major (includes
items 6, 14, and fluid section service kit,
minor P/N 144-050)
47474 Fluid section service kit, minor, LC 840
(includes items 1, 3, 4, 10, 12, 15, 18,
20, and Loctite P/N 426-051)
47478 Fluid section service kit, minor, LC 860
0555677 Foot valve assembly
(includes items 17–21)
0555678 Outlet valve assembly
(includes items 9–13)
© Wagner. All rights reserved.
6
14
7
8
15
3
16
4
17
18
9
19
10
20
11
12
21
13
Quantity

Servicing the Fluid Section

Use of non-Wagner service parts may void warranty. Ask
for original parts made by Wagner for best services. This
pump should receive a routine servicing after approximately
1,000 hours of use. Earlier servicing is required if there is
excessive leakage from the top packing or if pump strokes
become faster on one stroke or the other. The use of
Wagner EasyGlide (P/N 0508619) is recommended as an
upper packing lubricant. Do not substitute oil, water, or
solvent for an upper packing lubricant.
NOTE: Numbers in parentheses refer to the item
numbers in the fluid section illustrations. If
there are two numbers, the first number
represents the item number for the LC 820 and
the second number represents the item
number for the LC 840/LC 860.
Disassembling the Fluid Section
1. Remove the siphon hose assembly. Unthread the foot valve
housing (20,21) and the pump cylinder (14) with a strap
wrench.
2. Slide the retainer ring (1) up with a small screwdriver, then
push the connecting pin (2) out.
3. Pull the displacement rod (6) through the lower cavity of
the motor/pump block.
4. Remove the Teflon o-ring (3), upper packing spring (5),
and upper packing set (4) from the motor/pump block.
5. Hold the displacement rod (6) in a vise by the flats at the
top of the displacement rod and remove the outlet valve
housing (13) with a wrench while holding the displacement
rod horizontal with wooden support, if necessary. Remove
the seal washer (12), outlet valve seat (11), outlet valve
ball (10), lower packing set (4), lower packing spring (9),
sleeve (8, LC 820 only), and spring retainer (7).
6. Using a 1/2" extension bar attached to a 1/2" drive
ratchet, insert the end of the extension bar into the square
opening of the foot valve cage (16,17) inside the foot
valve housing (20,21). Unscrew and remove the foot
valve cage along with the wave washer (16, LC 840/LC
860 only) from the foot valve housing.
7. Remove the Teflon o-ring (3), foot valve ball (17,18), foot
valve seat (18,19), and seat o-ring (19,20) from the foot
valve housing (20,21).
8. Remove the o-ring (15) from the pump cylinder (14)
Reassembling the Fluid Section
NOTE: Use Teflon tape on all threaded pipe
connections.
1. Place a new seat o-ring (19,20) into the groove in the
bottom of the foot valve housing (20,21).
2. Inspect the foot valve seat (18,19) for wear. If one side is
worn, flip the seat to the unused side. If both sides are worn,
install a new seat. Place the new or flipped seat (worn side
down) into the bore at the bottom of the foot valve housing
(20,21).
3. Place a new foot valve ball (17,18) onto the foot valve
seat (18,19). Using a 1/2" extension bar attached to a
1/2" drive ratchet, insert the end of the extension bar into
the square opening of the foot valve cage (16,17) and
screw the foot valve cage into the foot valve housing
(20,21). Torque the cage to 240 in./lbs. (20 ft./lbs.).
4. Place the wave washer (16, LC 840/LC 860 only ) on top
of the foot valve cage (16,17).
5. Insert a new Teflon o-ring (3) into the groove of the foot
valve housing (20,21). Lubricate the o-ring using oil or
grease.
23
CAUTION
GB
R