Werbung
Verfügbare Sprachen
Verfügbare Sprachen
in the USB device .
<ROOT>indicates the first level of the file system. Select the directory
of the programs to be imported with the up / down arrow keys. The "+"
and "-" down buttons respectively exit and enter the selected directory.
Press OK for export operations. A message displays the number of
programs directly copied from the oven's memory to the USB device.
Remove the USB device and replace the cap previously removed.
NOTE:
the message <NO directory="">indicates that the USB
device is missing or not inserted correctly into its slot
3.6.7.2 MODEL T64G (reference Fig. 31b)
This function can only be accessed if the Lock has not been enabled!!
If you wish to store the 2 characteristic values for a cooking operation
(temperature, cooking time), after setting them as required using the
arrow keys (see point 3.6.5), press the "Program" button.
The message "Pr01" will flash on the display (figure 31b item D). Select
the program to be stored with the "Up Arrow" and "Down Arrow". Press
OK to confirm.
•
EDIT
This function can only be accessed if the Lock has not been enabled!!
If you wish to modify a program that has already been stored, you must
first call it up by pressing the relative key 3.6.6., then modify the values
using the arrow keys. As soon as one of the two values is edited, the
control unit switches to manual mode. To store the new values, proceed
as already described in section 3.6.7.2.
NOTE: On T64G when using the special STEP and RETURN
programs, parameters are automatically modified every time a
baking parameter is changed!
3.6.8
"ECO STAND-BY"
The "Eco standby" key keeps the oven hot reducing gas consumption;
press this key for standby cooking mode.
The oven is provided with two types of stand-by:
-
- Eco Stand-by 1: this is enabled with the STAND-BY button (fig.
31-31b item 19). On T75G-TT96G-TT98G the display turns green
and a money box icon is displayed in the operating mode. On T64G,
the display will show the message "ECO1"
-
- Eco Stand-by 2: this is enabled by holding down the STAND-BY
button (fig. 31-31b item 19). In this case besides reducing gas
consumption, the conveyor belt is stopped to preserve its parts from
wear. On T75G-TT96G-TT98G the display will show the icon for
the "belt stop" function. On T64G, the display will show the
message "ECO2"
In both cases, hold the button to disable the key STAND-BY.
NOTE:
The "Eco Standby" mode is similar to an "idle alert of
"the oven and cannot be used during cooking, otherwise food quality
would be compromised.
NOTE:
The function can be enabled only if the oven is in start
mode.
3.6.9
"HOTKEY"
( T75G-TT96G-TT98G only)
The "Hotkey" button ("star key") is a direct access custom button with a
specific function selected by the user.
Enter the "Hotkey" menu to view the current setting represented by the
selected item. To assign the "Hotkey" button a different function, move
the selected item with the up/down arrow keys to the desired entry and
press OK to confirm.
If required press the RETURN key to return to the main screen.
Press the HOTKEY to directly enable the selected function.
3.6.10 SPECIAL FUNCTIONS "STEP" AND "RETURN"
"Step" is used for discontinuous mode operations which enables the
conveyor belt manually for a single baking step.
The "Return" function can be used for baking times longer than the
maximum allowed (or taking out of the oven from the same side on which
it is placed in the oven) and provides for the possibility of activating the
conveyor belt for a double baking step.
T75G-TT96G-TT98G
To enable special functions "Step" and "Return" (if provided) go to
MENU, select "Special functions" then choose the desired function using
the OK key. The conveyor belt is stopped, the display turns orange, the
selected special function and inactive conveyor belt icons activate.
Place the product to be baked on the conveyor belt, then press HOTKEY
to start baking: the conveyor belt will begin to move to allow baking
within the set time plus the time necessary to let out the product. After
this, the belt will stop until you press HOTKEY again.
To go back to normal functioning, press STOP.
If between the end of a baking process and the next step over 2 minutes
pass, the oven automatically enters "Eco Stand-by 2" mode. Just press
HOTKEY to resume baking.
T64G
The T64G as well as providing 20 programs, also has two special
programs: STEP and RETURN.
The STEP program (indicated in the D display by "StEP") can be used
when there is a work pause. It enables the conveyor belt for a single
baking step. To use this program, select the STEP item from the program
list. The conveyor belt then stops. Place the product at the edge of the
belt, then press the "P / Hotkey" to start baking: the belt will start moving
to allow the transit of the product in the set time. After this the belt will
stop until you press "P / Hotkey".
The RETURN program (shown in the D display by "rEtu") can be used
for baking times higher than the maximum allowed (or taken out of the
oven on the same side in which it is placed in the oven). The conveyor
belt can then be enabled for a double baking step. To use this program,
select the RETU item from the program list. The conveyor belt will then
stop. Place the product at the edge of the belt, then press the P / hotkey to
start baking. The belt will start moving, then the first products will be
received within the time set then the second ones in the opposite direction
also within the baking set time. Example: 12 minute set cooking time, for
a total cooking time of 24 minutes. This setting is not provided for
standard operations.
NOTE:
When using the special STEP and RETURN programs,
after 2 minutes from the last bake, if no key is selected, the oven
automatically enters the ECO STAND-BY mode.
Once a new bake or a different cooking program is selected, the oven
returns to the standard setting mode.
3.6.11 CONVEYOR BELT SETTING
( T75G-TT96G-TT98G only)
Press MENU and select "Conveyor Belt" to access the conveyor belt
settings. There are two functions:
-
"Conveyor Belt Lock" it stops the conveyor belt while the gas power
and cooking parameters supplied is intact. Press OK to enable . The
conveyor belt stops and the icon status of the conveyor belt is
displayed in orange (enabled ).
NOTE:
The conveyor belt lock can be enabled also by
setting the "Cooking time" parameter to 00:00.
-
"Start / Stop" is enabled by default; this function allows the conveyor
belt to start only when the set temperature is reached after a sequence
of beeps. This ensures the conveyor belt components wear less, and
a lower heat exchange between the cooking and the outside chamber
during the heating and cooling process.
-
"Reverse" function (if provided): if enabled, it reverses the direction
of travel of the conveyor belt (see 5.8.3).
In both cases a check mark (√) to the right of the menu item, indicates
if the function is enabled.
3.6.12 "LOCK/UNLOCK"
This function can be used to block certain operations, for safety
purposes.
The following functions are disabled:
-Storage/modifying and deleting programs
-Changing cooking parameters
The following functions are still enabled:
-Use of programs
-Select "Eco standby", "Step", " "Conveyor Belt Lock
NOTE:
when LOCK is enabled, all unauthorised operations
are displayed on the main screen by the intermittent LOCK icon.
•
ACTIVATION/DEACTIVATION
T75G-TT96G-TT98G
To enable the "Lock" access MENU , select "Lock/Unlock" and press
OK. Select "Lock" and press OK. The display requires a four digit
secret password. To enter pass word use the up/down arrow keys to
select the desired number and press OK. When the control unit is
delivered, 1 1 1 1 is set as password. If the password entered is correct,
a message to confirm unblocked status is displayed and redirected
automatically to the main screen where the LOCK status icon displays
a closed padlock. If a wrong password is entered, a message will inform
the user to re-enter the password.
To disable the "Lock" access menu, select "Lock/Unlock" and press OK.
Select "Unlock" and press OK. Enter the password with the same
UK/12
Werbung
