Moretti Forni T Serie Bedienungsanleitung Seite 49

1) set point temperature/temperature detected
2) cooking time (production processing in the oven)
3) explanatory status messages
4) indication of the oven status (idle/heating/cooking)
5) working mode status (Manual, Program, Stand-by)
6) "Start Timer" status (not available for gas ovens)
7) "Conveyor belt Lock" status
8) "Step" status
9) "Lock" status
The oven's image appears at the center of the screen. The set-point
temperature is displayed in red above this image, to the right of which is
the icon of a flame representing the burner's status: the broken flame
indicates that the burner is off and the coloured flame indicates that the
burner is on or powering up.
TT96G-TT98G: Since the oven is provided with two burners, there are
2 flames displayed; positioned on the left and right of the set point
temperature, they indicate the status of the oven's left and right burner
(fig. 30b).
To the right of the central image of the oven is an indication, in red, of
the cooking time below which generic messages are indicated such as
date, time, oven model, oven status, etc ...inside a red label.
To the left of the screen starting from the top is the oven's status icon
represented by a gray lightning bolt indicating that the oven is off; it
turns red when the oven is heating and green when the oven is ready for
cooking. Below, the working mode icon, is represented by 'M' If the
manual mode is enabled, by 'P ' If a cooking program is enabled or the
symbol of a money box if "Eco standby" is enabled. The "Start Timer",
"Conveyor belt Lock" and "Step" status icon turn gray if the key is
disabled and orange if the key is enabled. The unlocked padlock icon
indicates that the "Lock" key is disabled; it switches to a closed padlock
icon in orange if the key is enabled.
T64G (fig.31b):
The oven is turned on by setting the main switch (fig.31b item E) to position
"1".
When turned on, the control panel will identify the following settings:
A. baking chamber inside temperature
B. set temperature (Set Point)
C. set cooking time
D. status display, for displaying the status of the equipment or of any
abnormalities detected
3.6.3 THE KEYPAD
T75G-TT96G-TT98G (fig. 31)
The buttons on the control panel are the following (its use will be
explained below:
10) -: decrease parameter
11) +: increase parameter
↑ and ↓ : "Up/Down" arrow keys
12)
13) Access to menu settings ("Menu")
14) Program management P ("Program")
15) Ok confirm
16) Delete, go back without confirming ("Return")
17) Ignition ("Start")
18) Off ("Stop")
19) Enable/disable Eco Standby function ("Stand-by")
20) Custom key ("Hotkey")
NOTE:
LCD not TOUCH SCREEN. If the display is pressed,
this can cause permanent damage which may stop the oven from
functioning properly.
T64G(fig.31b):
The keys to the right of the display (details of their uses will be given
later in the manual) are the following:
12) up arrow / +
13) down arrow / -
14) right arrow
15) left arrow
16) OK button
17) Start/Stop button
18) program key P/Hotkey
19) Eco Stand-by key
20) Lock button
3.6.4 OVEN START-UP
When switched on, the control panel will first show the initial screen
complete with the settings for the last baking operation carried out
(T75G-TT98G fig.30, T64G fig. 31b).
T75G -TT96G-TT98G
The operating mode icon indicates the previous cooking mode manual
("M") or program set or ("P").
Press STA RT (fig. 31 item17 to operate the oven after a few seconds
the fan inside the oven and burner is activated. The temperature icon
starts to alternate the red set-point temperature displayed with the
gauged white temperature; the icon representing the flame status is
coloured, the status icon turns red and the message bar concurrently
indicates that the heating process has begun .The configuration will hold
until the oven reaches the set point temperature.
The conveyor, by default is activated only when it reaches the working
temperature, as described in 3.6.11.
NOTE:
EACH TIME THE OVEN MUST REACH THE SET
TEMPERATURE
CHANGE, THE ELECTRONIC REGULATION REQUIRES A
FEW MINUTES FOR DIRECT ULTIMATE CALIBRATION;
WAIT FOR THE TEMPERATURE TO BE STABILIZED
BEFORE BAKING, OTHERWISE THE FOOD WILL NOT
COOK PROPERLY
NOTE:
If the START key is not pressed when the oven is
turned on, the display enters power save mode after a limited set
time and goes black. Press any key on the unit to configure display.
T64G:
The display (figure 31b item D) will show previous cooking mode:
manual or preset program.
If you wish to start cooking, press the "Start" button (fig. 31b item 17)
after which the heating elements, the belt and the fan inside the oven will
start (fig. 31b item D). The screen will show the message "HEAT", which
will flash until the set point temperature is reached. If the set point
temperature is reached, a message will appear on screen with "GO" after
which you can start cooking. The dot in the temperature display indicates
if power is supplied.
NOTE:
The temperatures of the top and floor (not linked to
each other) can have a maximum range of 15 ° of difference,
beyond such range both reaching the set temperatures and the full
functionality of the equipment are no longer guaranteed.
3.6.5 SETTING AND MODIFYING COOKING
PARAMETERS:
This function can only be accessed provided the Lock has not been
enabled!!
To reset parameters before starting the oven (temperature, cooking time)
press + and – to change the set-point temperature and the arrow keys
up/down to edit cooking time.
On T64G, the corresponding display will flash to show the setting has
been selected; you can select three settings: temperature, baking time and
baking program. The selected setting will start flashing. If you select the
"baking program" setting, the temperature display will show the set point
for that program.
Once the required value has been selected, use the up and down arrow
keys to change the value.
NOTE:
The above operation can also be performed when
cooking; if you're on a generic program press "esc" and
automatically enter the manual "mode".
- Maximum temperature set point:
400 °C / 752°F (T75G) o 320°C / 608°F (T64G-TT96G-TT98G).
-Minimum cooking time:
2 minutes (optional: T75G TT96G TT98G 45").
30 seconds (T64G)
- Maximum cooking time:
20 minutes (optional T75G-TT96G-TT98G 10').
The conveyor belt gear motor is fitted with a reverse rev control which
(only for T75G-TT98G)
an even transit time. Cooking time can also be set at zero and the
conveyor belt will stop while the "conveyor belt lock" icon status will be
enabled.
To check the transit time on T75G it is necessary to measure the time
from the moment of entry at the outer side of the baking chamber to the
moment of exit at the outer side of the baking chamber.
To check the transit time on T64G,TT96G, and TT98G, it is necessary to
measure the time from the moment of entry at the outer side of the baking
chamber to the moment of exit at the outer side of the baking chamber.
UK/10
AT STARTUP ANDTEMPERATURE
, regardless of the weight on the belt, guarantees