Herunterladen Inhalt Inhalt Diese Seite drucken

WAGNER 0556730W Betriebsanleitung Seite 25

Vorschau ausblenden Andere Handbücher für 0556730W:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

13. Clean and inspect all parts. Inspect displacement rod's (6)
and cylinder's (12) chrome for grooves, dents or worn areas.
Replace if hard chrome is damaged. Inspect valve seats and
replace if cracked or worn.
Reassembly Procedure
If cylinder (12) and displacement rod (6) are
i
reusable, then only a minor kit part # 155-051 or
155-055 may be required for reassembly.
1. Insert upper packing set (19) into pump block (21).
Peak of "V" packings must point upwards on
reassembly.
Attention
2. Insert upper spring (18).
3. Place new lower packing set (14) over piston seat (13).
Peak of "V" packings must point downward on
reassembly.
Attention
4. Replace spring (15), washer (16) and ball (17) on piston seat
(13).
5. Thread piston seat (13) back onto displacement rod (6).
i
use Loctite (Part # 426-051) on clean threads.
6. Insert displacement rod (6) assembly through upper packing
set (19) in pump block (21).
7. Place O-ring (20) on end of cylinder (12) and thread back into
pump block (21).
i
Lubricate all O-rings before assembly (EasyGlide,
Part # 0508619).
8. Insert new ball (11), ball cage (10) and ball stop (9) into foot
valve (7).
9. Place new Teflon O-ring (8) on cylinder (12) and then install
foot valve assembly (7).
It is not necessary to overtighten foot valve and
i
cylinder into pump block. O-ring seals perform
sealing function without excessive tightening. Full
thread engagement is sufficient. The foot valve
(7) may be rotated back up to 1/2 turn from full
engagement for convenient hose position.
10. Insert connecting rod (5) through coupling nut (4) and thread
connecting rod (5) into displacement rod (6).
11. Hold the air motor piston rod (3) at the wrench flats and
thread coupling nut (4) to secure the pump to the motor.
12. Using the stanchions, the stanchion nuts (1) and washers (2),
secure the pump assembly to the bottom of the unit.
13. Replace the two halves of the shield assembly . Secure the
two halves to each other with screws and secure the entire
assembly to the plate (11) with the four screws.
14. For siphon hose attachment, it is critically important that the
thread of the siphon hose fit snugly into the foot valve with
the hose assembly couplings Teflon-taped and sealed to
prevent air inlet leakage.
SuperCoat
GB
Service Kits
i
The minor service kits for pump assembly 155-
559 come in two versions. They include kits with
1) Polyethylene/Leather packing and 2) Leather
packings.
Service Kits
155-559 pump service kit, minor
Kit Part
Packings*
No.
155-055
Polyethylene/
leather
155-051
Leather
155-559 pump service kit, major
155-505
Polyethylene/
leather
155-500
Leather
* Refer to the Spare Parts List for pump assembly 155-559 for
the part numbers of each type of upper and lower packings.
23
Description
Includes items 9, 11, 14, 17, 19, 20 (2),
and Loctite sealant 426-051
Includes items 9, 11, 14, 17, 19, 20 (2),
and Loctite sealant 426-051
Includes minor service kit 185-050 and
items 6, 12 and 18
Includes minor service kit 185-051 and
items 6, 12 and 18
Servicing

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis