Herunterladen Diese Seite drucken

Panasonic CQ-G26EG Servicehandbuch Seite 48

Werbung

6. M.G
PLATE
ASS'Y
INSTALLATION
1) Pass
bosses
D1
and
D2
of the M.G
Plate Ass'y (35)
through square holes D1' and
D2' of the Chassis Ass'y
(i) (D1 — D1', D2 — D2'), (Fig. 6-1)
2) Insert
the boss
of the Turn
Over
Gear
3) into the
hole of the Turn Over Gear Collar Qf) which is placed
in the groove of the Change Plate Ass'y @. (Fig. 6-2a)
3) Engage holes
E1 and
E2 of the M,G
Plate Ass'y with
studs
Et' and
Ez'
of the Chassis
Ass'y
and
slightly
press them down. (Fig. 6-1)
4) Rotate
the Main
Gear (04) (or the Motor
Pulley}
so
that gears are engaged well.
5) Press
FF
anc
REW
Levers
at
the
same
time
to
fix aground
of the T.S Actuator a0. When the M.G
Plate Ass'y is put back in its specified place, fix it with
two camera screws 93). (Fig. 6-1)
—— (99 Camera Screw
|
M.G Plate Ass'y 68)-—
EN K e y
g n Ei
>
Chassis Ass'y (209)
E.S Plate
Chassis Ass'y
a
(M) Control Spring
(Fig. 6-3a)
a
6) Install the T.G Actuator @). (Fig. 6-2)
7) Install the Main Plate @08). (Fig. 6-2)
Note:
After
installation, confirm
the relation of posi-
tion F ~ Jin the Fig. 6-2b.
8) Install
the
Control
Spring
Qi). Insert it in between
the F.R Lock Plate an and the Chassis Ass'y. (Portion
K in the Fig. 6-3a).
;
9) Install
a F.R Actuator
a). (Set one side in the groove
of the F.R Slide Plate (1) . (Fig. 6-3)
10) Install the Main Belt.
Note:
Re-install the Main Belt
as shown Fig. 6-4.
Turn Over Gear Collar
(2§] ~S5|S
>
'
Turn Over Gear
Change Plate Ass'y 08)
|
ve)
ex
(Fig. 6-2a)
T.G Actuator (24)
(Fig. 6-2)
Stop Arm
T.G Plate (F) Ass'y
Main Plate
T.G Plate (R)
Take Up Reel
Sub Ass'y
T.G Actuator
T.G Push Plate
(Fig. 6-2b)
Motor Pully
— 50 —
7. CASSETTE
CASE
INSTALLATION
1) Insert the boss of the Chassis Ass'y (03) into the notch
of the Lift Up Lever @ij). (Fig. 7-1)
Chassis Ass'y aoe
@i}) Lift Up Lever
(Fig. 7-1)
Slightly press the Chassis Ass'y
(Fig. 7-3a)
(before pushing in the Push Lever Ass'y)
bent portion of
Cassette Case
Lift Up Lever
=
Text
buring portion of
a gid P.E Spring
Long Side
Short Side —-
Case Lifter aih—
(Fig. 7-2)
C.D Plate @)—
KA Middle finger
Ke
Third finger
(
Little finger
Push Lever Ass'y @)—~
(Fig. 7-3b)
(Completion)
(Fig. 7-4)

Werbung

loading

Diese Anleitung auch für:

Cq-g21eg