Warranty Exclusions - Triton TCMS 254 Sicherheits- Und Bedienungsanleitung

Vorschau ausblenden

Inhalt

Seite von 97

/ 97
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

Replacing the blade (Fig. XIX, XX, XXI, XXII)

WARNING: Unplug the mitre saw before changing/installing the Blade (28).

1) Select a 254mm Blade with a 25.4mm arbour, making sure the rotation arrow on

the Blade matches the clockwise rotation arrow on the upper guard, and the

Blade teeth are pointing downward

2) Place the Blade, the Outer Blade Collar (71) against the Blade and on the arbour.

Thread the Arbour Bolt (69) on the arbour in a counter clockwise direction

IMPORTANT: Make sure the flats of the blade collars are engaged with the flats on

the arbour shaft. Also, the flat side of the blade collar must be placed against the

Blade (28).

3) Place the Blade Spanner (35) on the Arbour Bolt

4) Press the Arbour Lock (70), holding it in firmly while turning the Blade counter

clockwise. When it engages, continue to press the Arbour Lock in, while

tightening the Arbour Bolt securely

5) Rotate the Cover Plate (68) and Lower Blade Guard (3) back to its original

position

6) Replace the the Cover Plate Screw (67) and tighten with a Phillips screwdriver.

7) Verify the operation of the Lower Blade Guard does not bind or stick

8) Be sure the Arbour Lock is released so the Blade turns freely

Replacing the guide fence (Fig. XXIII)

IMPORTANT: The left side Guide Fence (11) must be removed when making any

right bevel angle cuts greater than 33.9° in combination with any right or left mitre

angle. This Guide Fence must also be removed when making left bevel cuts greater

than 40° with a mitre angle greater than 31.6°.

1) Unlock the Guide Fence Locking Lever (24) by pushing it out towards the rear of

the saw.

2) Align the Guide Fence Slot (72) with the Guide Fence Rear Bolt (73) in the rear

of the Guide Fence, and then lift up the Guide Fence to remove it from the saw.

3) To replace the Guide Fence, align the Guide Fence Slot with the Guide Fence

Rear Bolt in the rear of the Guide Fence to place the Guide Fence onto the mitre

saw fence.

4) Slide the Guide Fence to align the Back Nut (74) with the Back Slot (75).

5) To lock the Guide Fence, push the Cam Locking Lever (24) in towards the front

of the saw.

Carbon brushes (Fig. XXIV)

WARNING: Always disconnect the plug from the power source before inspecting

the brushes.

•

Check the motor brushes after the first 50 hours of use for a new machine or

after a new set of brushes have been installed.

•

After the first check, examine them every 10 hours of use. When the carbon is

worn to 6 mm in length or if the spring or shunt wire is burned or damaged,

replace both brushes.

•

If the brushes are found serviceable after removing, reinstall them.

•

To inspect or replace brushes, first unplug the saw. Next, remove the two Fixing

Screws (76) and the motor Rear Motor Cover (77) from the motor. Carefully

remove the Spring-Loaded Cap (78) on the side of the motor. Third, pull out the

Carbon Brush (79) and replace. The ears on the metal end of the assembly go in

the same hole the carbon part fits into. Last, tighten the cap snugly, but do not

overtighten.

•

Repeat above procedure for the Carbon Brush located on the other side of the

motor.

Note: To reinstall the same brushes, first make sure the brushes go back in the way

they came out. This will avoid a break-in period that reduces motor performance and

increases wear

Contact

For technical or repair service advice, please contact the helpline on

(+44) 1935 382 222

Web: tritontools.com/en-GB/Support

Address:

Toolstream Ltd.

Boundary Way

Lufton Trading Estate

Yeovil, Somerset

BA22 8HZ, United Kingdom

tritontools.com

Guarantee

To register your guarantee visit our web site at

tritontools.com* and enter your details.

Purchase Record

Date of Purchase:

___ / ___ / ____

Model: TCMS254

Retain your receipt as proof of purchase

Triton Precision Power Tools guarantees to the purchaser of this product that if

any part proves to be defective due to faulty materials or workmanship within

3 YEARS from the date of original purchase,

Triton will repair, or at its discretion replace, the faulty part free of charge.

This guarantee does not apply to commercial use nor does it extend to normal

wear and tear or damage as a result of accident, abuse or misuse.

* Register online within 30 days.

Terms & conditions apply.

This does not affect your statutory rights

Australian Warranty Information

You may wish to register your product at www.tritontools.com but you are not

under any obligation to do so.

Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law. You are entitled to a replacement or refund for a major failure

and for compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to

be of acceptable quality and the failure does not amount to a major failure.

This product is guaranteed against faulty materials and workmanship for

3 YEARS from the date of purchase. Please retain your receipt as proof of

purchase.

This warranty does not cover defects caused by or resulting from:

(a) misuse, abuse or neglect;

(b) trade, professional or hire use;

(d) damage caused by foreign objects, substances or accident.