Introduction; Device Description (Fig. 1-11); Scope Of Delivery; Proper Use - Parkside PTBMOD 710 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

2. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
In accordance with the applicable product liability laws, the
manufacturer of this device assumes no liability for damage to
the device or caused by the device arising from:
• Improper handling
• Failure to comply with the operating instructions.
• Repairs carried out by third parties, unauthorised specialists.
• Installing and replacing non-original spare parts,
• Improper use
• Failures of the electrical system in the event of the electri-
cal regulations and VDE provisions 0100, DIN 57113 /
VDE0113 not being observed.
Note:
Read the whole text of the operating manual before assembly
and commissioning.
This operating manual should help you to familiarise yourself
with your device and to use it for its intended purpose.
The operating manual includes important instructions for safe,
proper and economic operation of the device, for avoiding
danger, for minimising repair costs and downtimes, and for
increasing the reliability and extending the service life of the
device.
In addition to the safety instructions in this operating manual,
you must also observe the regulations applicable to the opera-
tion of the device in your country.
Keep the operating manual at the device, in a plastic sleeve,
protected from dirt and moisture. They must be read and care-
fully observed by all operating personnel before starting the
work.
The device may only be used by personnel who have been
trained to use it and who have been instructed with respect to
the associated hazards. The required minimum age must be
observed.
In addition to the safety instructions in this operating manual
and the separate regulations of your country, the generally
recognised technical rules relating to the operation of such ma-
chines must also be observed.
We accept no liability for accidents or damage that occur due
to a failure to observe this manual and the safety instructions.

3. Device description (fig. 1-11)

1. Base plate
2. Quick clamp
3. Column
4. Toothed rack for height adjustment
5. Clamping lever for height adjustment
6. Clamping lever for depth stop
7. Depth stop
8. Handle
9. Pointer, depth stop
10. Off switch
11. On switch
12. Speed control
13. Spacer
14. Chuck
15. Wing screws for parallel stop
16. Parallel stop
17. Quick-clamp screw
18. Laser ON/OFF switch
19. Phillips screw (pointer)
20. Scale
21. Allen key, 4 mm
22. Chuck key
23. Marking

4. Scope of delivery

• 1 Drilling machine
• 1 Quick clamp (2)
• 1 Base plate (1)
• 1 Parallel stop (16)
• 1 Spacer (13)
• 1 handle (8)
• 1 Depth stop (7)
• 1 Clamping lever (6)
• 1 Allen key, 4 mm (21)
• 1 Chuck key (22)
• 1 Operating manual
• 1 Assembly material

5. Proper use

The bench drill is designed for drilling in metal, wood, plastic
and tiles.
Chuck clamping range: 1.5 - 13 mm.
The device is only intended to be used for DIY purposes. It
was not designed for continuous commercial use. The device is
not intended for use by people under the age of 16. Children
under the age of 16 may only use the device when supervised.
The manufacturer is not liable for damage caused by improper
use or incorrect operation.
Please observe that our equipment was not designed with the
intention of use for commercial or industrial purposes. We as-
sume no guarantee if the equipment is used in commercial or
industrial applications, or for equivalent work.
GB 3