Transport; Cleaning And Maintenance; Storage; Electrical Connection - Parkside PTBMOD 710 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

3. For drilling, move the handle (8) with uniform feed until
the desired drilling depth is reached. When drilling into
metal, interrupt the downward pressure briefly to break
the swarf.
4. After reaching the drilling depth, return the handle (8) to
the starting position.
5. Switch the device off.

11. Transport

m Warning! Unplug the mains plug prior to transport!
• To transport the device hold it by the base plate (1).

12. Cleaning and maintenance

m Warning! Pull out the mains plug before carrying out any
adjustments, maintenance or repair work!
12. 1 General maintenance tasks
m Have tasks that are not described in this operat-
ing manual performed by a specialist workshop.
Use only original parts. Let the device cool down
before all maintenance and cleaning tasks.
m There is a risk of burn!
Before using the device each time, check the device for obvi-
ous defects such as worn or damaged parts, correct seating of
screws or other parts. Replace damaged parts.
12.2 Cleaning
Do not use cleaning agents or solvents. Chemical substances
could damage the plastic parts of the device. Never clean the
device under running water.
• Clean the device thoroughly after each use.
• Clean the ventilation holes and the surface of the device with
a soft brush or cloth.
• Remove swarf, dust and dirt with a vacuum cleaner if neces-
sary.
• Lubricate the moving parts regularly.
12.3 Maintenance
The device has no parts that require maintenance.
12.4 Replacing the chuck (fig. 1, 5, 10)
m Warning! Pull out the mains plug!
Tools required (not included in the scope of delivery):
1x open-ended wrench 27 mm
• Remove the insert tool as described in 10.3.2.
• Tighten the clamping sleeve (D) firmly by turning the chuck
key (22) clockwise.
• Hold the chuck (14) with one hand while using the open-
ended wrench (27 mm) to lower the nut (F) clockwise.
• Once the chuck (14) is loosened from the shaft seat, it can
be removed.
• Fasten the new chuck in reverse order.
When replacing the chuck, use only chucks approved by the
manufacturer.
Order number: 390 6814 001
8 GB
12.5 Service information
With this product, it is necessary to note that the following parts
are subject to natural or usage-related wear, or that the follow-
ing parts are required as consumables.
Wear parts*: Carbon brushes, drill bit
* may not be included in the scope of supply!

13. Storage

Store the device and its accessories in a dark, dry and frost-
free place that is inaccessible to children. The optimum storage
temperature lies between 5 and 30 °C.
Store the electric tool in its original packaging.
Cover the electric tool to protect it from dust or moisture.
Store the operating manual with the electric tool.

14. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer's mains connection as well as the extension
cable used must also comply with these regula-
tions.
14.1 Important information
In the event of overloading, the motor will switch itself off. After
a cool-down period (time varies) the motor can be switched
back on again.
14.2 Faulty power supply cables
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Pressure points, where connection cables are passed through
windows or doors.
• Kinks where the connection cable has been improperly fas-
tened or routed.
• Places where the connection cables have been cut due to
being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Ensure that the connection cables are disconnected from elec-
trical power when checking for damage.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables with the
marking H05VV-F.
The printing of the type designation on the connection cable
is mandatory.
If it is necessary to replace the connection cable, this must
be done by the manufacturer or their representative to avoid
safety hazards.
14.3 AC motor
The mains voltage must be 220 - 240 V ~ 50Hz.
• Extension cables up to 25 m long must have a cross-section
of 1.5 mm .
2