Technical Data; Before Commissioning; Assembly - Parkside PTBMOD 710 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

7. Technical data

AC motor....................................................220 - 240 V ~ 50 Hz
Nominal power S1 ...................................................... 710 Watt
Operating mode ...............................................S2 5min* 900W
Idle speed n ....................................................500 - 2600 min
0
Drill chuck clamping range .....................................1.5 - 13 mm.
Max. drill stroke.................................................................70 mm
Size of base plate ...............................................320 x 305 mm
Distance chuck to bottom plate ..................................... 280 mm
Weight approx. ..................................................................8,3 kg
Protection class ................................................................... II /
Laser class ................................................................................... 2
Laser wavelength ............................................................. 650 nm
Laser power .....................................................................< 1 mW
* After an uninterrupted operating period of 5 minutes, the de-
vice should be allowed to rest until its temperature has dropped
to within 2 K (2° C) of room temperature.
The workpiece must have a minimum height of
3 mm and a minimum width of 45 mm.
Make sure that the workpiece is always secured
with the clamping device.
Overhanging workpieces may have to be support-
ed laterally by additional supports.
Noise
The noise levels have been determined in accordance with EN
62841.
Sound pressure level L ............................................ 89,6 dB(A)
pA
Uncertainty K ......................................................................3 dB
pA
Sound power level L ............................................102,6 dB(A)
WA
Uncertainty K .....................................................................3 dB
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing.
The above-mentioned noise emission values were measured in
accordance with a standardised test procedure and can be
used to compare one power tool with another.
The specified device emissions values can also be used for an
initial estimation of the load.
Warning:
• The noise emission values can vary from the specified values
during the actual use of the electric tool, depending on the
type and the manner in which the electric tool is used, and in
particular the type of workpiece being processed.
• Try to keep the stress as low as possible. For example: Limit work-
ing time. In doing so, all parts of the operating cycle must be taken
into account (such as times in which the electric tool is switched off
or times in which it is switched on, but is not running under a load).

8. Before commissioning

• Open the packaging and carefully remove the device.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport damage.
6 GB
• If possible, keep the packaging until the expiry of the war-
ranty period.
ATTENTION
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
-1
films or small parts! There is a danger of choking
or suffocating!
Before connecting the machine, make certain that the data on
the type plate matches with the mains power data.
• Check the device for transport damage. Immediately report
any damage to the transport company that delivered the
electrical tool.
• Long supply cables (extension cable) should be avoided.
• Do not operate the electrical tool in damp or wet areas.
• Operate the electrical tool only in suitable areas (well ven-
tilated).

9. Assembly

m Attention!
Always make sure the device is fully assembled before com-
missioning!
m Before connecting the machine to the mains power, make certain
that the data on the type plate matches with the mains power data.
m Warning! Always pull out the mains plug before carrying
out adjustments on the device.
9.1 Assembling the base plate and column (fig. 2)
1. Slide the quick clamp (2) over the column (3).
2. Set the column (3) into the base plate (1) such that the
guide pins on the bottom end of the column (3) engage
with the groove in the mount on the base plate (1).
3. Tighten the pre-assembled fastening screws (A) on the
rear of the base plate (1) with the Allen key (21).
9.2 Fitting the parallel stop (fig. 4)
1. Slide the parallel stop (16) into the grooves in the base
plate (1).
2. Ensure that the sliding blocks underneath the wing screws
of the parallel stop (15) are properly engaged in the
grooves of the base plate.
3. Move the parallel stop (16) to the desired position and
tighten the wing screws of the parallel stop (15) firmly.
9.3 Assembling the handle (fig. 2)
1. Remove the pre-assembled fastening screw (B).
2. Ensure that the spacer (13) is seated correctly.
3. Slide the handle (8) onto the retainer (G) as shown in fig. 2.
4. Place the nut (C) in the recess in the handle (8) and tight-
en the fixing screw (B).
9.4 Fitting the depth stop (fig. 2)
1. Insert the depth stop (7) from above into the recess in
the housing.
2. Assemble the clamping lever for depth stop (6) as shown
in fig. 2.