Wolf Garten UV 38 BX Gebrauchsanweisung Seite 14

Safety instructions
fter Work
• Do not park the device in a closed room immediately after work, but
rather allow it to cool down outdoors.
• Before leaving the device, pull the spark plug connector and, if
present, take out the ignition key.
• Lifting the device for transport:
- never do so with the engine running, nor when the engine is hot
and only with the spark plug socket pulled out.
• When folding it up, take off the starter rope and be sure the cables
do not get bent
• lways only change the oil with the tank empty and closed, and with
the engine warm.
ssembly
Open the grip rod assembly (Fig. M1)
IMPORT NT: When opening the grip rod assembly, the
cable must not get squeezed.
Lift the top part and bottom part of the grip and fold to the
rear.
Fasten the bottom part of the grip (Fig. M2)
Lock the bottom part of the grip into place in the recesses and
tighten the handwheels by turning them ( ).
IMPORT NT: The cable must not get squeezed.
Fasten the height adjustment (Fig. M3)
Move the Work Control Lever (B) forward.
remove the winged nut along with bolt and washer. Lift the
top part of the grip so that the lower connecting rod (C) and
the upper connecting rod (D) can be brought together in the
plastic part (E). Connect the two connecting rods with the
winged nut, bolt and washer.
Fastening the top part of the grip (Fig. M4)
pplying slight pressure, move the top part of the grip to the
rear and tighten the handwheels (F).
14
All manuals and user guides at all-guides.com
Maintenance
• Check the catching device frequently for wear or deformation.
• For safety reasons, replace any worn or damaged parts. When
• Maintenance and cleaning work on the device or removing the pro-
• If the device has to be tilted for maintenance work, first the fuel has
• If the fuel tank has to be emptied, this should be done outdoors. Be
• Clean the device after every use with a hand brush not with water,
• Do not park the device in moist rooms or near open flames or any-
• Check all the visible fastening bolts and nuts regularly to be sure
• Only use spare parts made by WOLF; otherwise you do not have a
Mounting the starter rope (Fig. M6/D)
Unscrew and
Only move the top part of the grip (Figs. M4/M5)
Fold up the complete grip rod assembly (Fig. M1)
replacing, follow the instructions for installation.
tective equipment may only be carried out with the engine stopped
and the spark plug connector pulled off and – if present – the ignition
key taken out.
to be removed from the tank entirely.
sure that no fuel gets spilt.
and in particular, do not spray with high pressure. Be sure the cool-
ing fins on the cylinder are clean and that the intakes are clean.
where where a spark could ignite petrol gases.
they are snug and tighten them.
guarantee that your scarifier meets safety regulations.
nti-kink protection(Fig. M4)
IMPORT NT! The cable must always lie in the anti-kink
protector M4 (G).
Lift Safety Bar D (2) and hold it. Slowly draw the starter rope
to the grip bar connection, and twist into the guide. Before
folding up the grip rod assembly, twist the starter rope back
out.
ttach the catcher sack* (Fig. M7)
Lift the protective shutter.
recesses in the chassis (see arrow), and put on protective
shutter.
(*TK 38, accessory available at an extra charge)
Only unscrew the handwheels on the top part of the grip M4
(F). Take off the winged nuts on the rod assembly of the
height adjustment M5, or loosen far enough for you to be able
to move the top part of the grip and connecting rod forward.
IMPORT NT: when folding up the grip rod assembly, the
cable must not get squeezed.
Unscrew the handwheels on the bottom part of the grip and on
the top part of the grip. Undo the winged nuts along with bolts
and washers from the connecting rods. Press the bottom part
of the grip out of the recesses.
ttach the catcher sack in the