Warranty - Kärcher B 110 R Originalbetriebsanleitung

Malfunction
Battery empty!
Open seat contact!
Switch on!
Restart machine!
Release throttle!
Malfunction
The device cannot be started 1. Sit in the driver's seat.
The water volume is insuffi-
cient
The suction performance is
too low
The cleaning results are un-
satisfactory
The brushes do not rotate
The device does not brake
The waste water drain hose is
clogged
The "Dose" detergent dosing
unit does not work

Warranty

The warranty conditions issued by our rele-
vant sales company apply in all countries.
We shall remedy possible malfunctions on
your appliance within the warranty period
Rectification
1. Set the program selector switch to transport travel.
2. Drive the device by the shortest route to the charger (or to the socket in the case of an internal
charger). Avoid gradients.
3. Charge the battery.
1. Relieve the driver's seat briefly so that the control can check the function of the seat contact switch.
1. Set the safety switch to "1".
1. Set the programme switch to "OFF".
2. Wait 10 seconds.
3. Set the program switch to the desired program.
1. Release the accelerator pedal.
Malfunctions without information shown on the display
Rectification
2. Take your foot off the accelerator before switching on the safety switch.
3. Turn the safety switch to "1".
4. Check the battery and charge if necessary.
5. Set the programme switch to "OFF".
6. Wait 10 seconds.
7. Set the program switch to the desired program.
8. If possible, only drive the device on level ground.
9. Check the parking brake if necessary.
If the fault still occurs, call Customer Service.
1. Check the fresh water filling level, if necessary fill the tank completely so that the air is pressed out.
2. Remove and clean the fresh water filter.
3. Insert the filter and screw on the cap.
4. Only with R cleaning head: Pull off the water distribution strip on the cleaning head.
5. Only with R cleaning head: Clean the water channel.
6. Check the hoses for clogging and clean if necessary.
1. Clean the seals between the waste water tank and the cover, check for leaks and replace if neces-
sary.
2. Check the fluff filter for soiling and clean if necessary.
3. Clean the suction lips at the suction bar, turn over or replace if necessary.
4. Close the lid on the waste water drain hose.
5. Close the cover of the waste water tank rinsing system.
6. Check the suction hose for clogging and clean if necessary.
7. Check the suction hose for leaks and replace if necessary.
8. Check the adjustment of the suction bar.
1. Set the appropriate cleaning program for the cleaning task.
2. Use suitable brushes for the cleaning task.
3. Use a suitable detergent for the cleaning task.
4. Reduce the driving speed.
5. Adjust the contact pressure.
6. Adjust the squeegee blades.
7. Check the brushes for wear and replace if necessary.
8. Check the water output.
1. Reduce the contact pressure.
2. Check if the brushes are blocked by a foreign body and remove the foreign body if necessary.
3. If the motor is overloaded, let the motor cool down.
4. Set the programme switch to "OFF".
5. Wait 10 seconds.
6. Set the program switch to the desired program.
7. Check that the plug of the device is plugged into the cleaning head.
1. Undo the brake lock (see "Operation / Pushing the device").
1. Open the dosing unit cover at the drain hose.
2. Pull the suction hose off the suction bar and close it by hand.
3. Set the programme switch to "Vacuum".
The blockage is sucked out of the drain hose into the waste water tank.
1. "Dose" version only: Call Customer Service.
free of cost, provided that a material or
manufacturing defect is the cause. In a war-
ranty case, please contact your dealer (with
the purchase receipt) or the next author-
ised customer service site.
(See overleaf for the address)
English 29