Remote Control Battery Change; Disposal; Manoeuvring The Caravan; Coupling To A Towing Vehicle - Truma Mover XT4 Gebrauchsanweisung, Einbauanweisung

LED 4 green flashes if radio connection has not yet been
established after switching on the remote
control
lights up when remote control is ready for
operation and the data link is stable
flashes in combination with acoustic signal
– 10 seconds after switching on the remote control if the
control unit is not yet ready for operation
– if the control unit has been switched off
– after 1 minute without pressing a button on the remote
control
– after a radio communication interruption
All LEDs "off" and no audio signal
System off (check batteries in remote control if necessary)

Remote control battery change

Please only use leak-proof micro-batteries with a steel outer
casing, type LR 03, AAA, AM 4, MN 2400 (1.5 V).
When inserting new batteries, take care not to reverse the
positive and negative terminals.
Figure 3
Empty, used batteries can leak and damage the remote
control! Remove the batteries if the remote control is
not being used for a long period of time.
No warranty is given for damage caused by leaking
batteries.

Disposal

Neither the remote control nor the batteries may be
disposed of with domestic refuse, instead they must be
sent for recycling separately via a collection point. By
doing this you are contributing towards reuse and recycling.

Manoeuvring the caravan

Follow the "Safety instructions" before using the
Mover® XT4.
Apply parking brake if caravan is uncoupled.
Disconnect 13-pin plug / adapter from vehicle and plug into
safety socket of caravan.
For safety reasons, the Mover® XT4 can only be operated
if the 13-pin plug / adapter of the caravan is plugged into
the safety socket.
In the event of a malfunction, the 13-pin plug / adapter
must not be removed from the safety socket until the
parking brake has been applied, since removing the plug dis-
ables the electronic safety functions.
Switch on the remote control – green LED 4 flashes until the con-
trol unit is ready for operation. If the control unit is not ready for
operation, the remote control switches off after about 10 seconds.
Press the two buttons (i) for engaging simultaneously, and en-
gaging will start after approx. 3 seconds (safety delay).
Use the position indicator to check that all drive rollers
are correctly engaged.
Before starting the Mover® XT4, release the parking brake.
The caravan can be moved in all directions using the control
knob and the slide control.
With the Mover® XT4 rotation around the vertical axis by about
30 cm per side (measured at the drawbar) can be carried out
with the end stop at the control knob (left and right stop)
The Softstart / Softstop makes the caravan start to move
without jolting, and brakes it gently when stopping.
When the control knob or slide control are released, or if the
radio signal is interrupted or becomes too weak, the caravan
stops moving. Radio equipment and other Mover® remote
controls will not activate your Mover®.
After start-up, the Mover® XT4 moves at a steady speed (ac-
cording to the setting on the slide control). Speed increases
slightly on downhill slopes and decreases on uphill slopes.
After manoeuvring, apply the parking brake first and then
disengage the drive rollers from the tyres.
Move slide switch on remote control to the "Off" position
to switch the remote control off (the Mover® XT4 switches to
standby mode).
The slide switch also acts as an "Emergency Stop"
switch.
Remove the plug / adapter from the safety socket after
manoeuvring, otherwise the control unit will automatically
switch off after 1 hour. When the plug / adapter is inserted,
the battery is discharged with a quiescent current of approx.
80 mA (with approx. 150 μA after one hour).

Coupling to a towing vehicle

The Mover® XT4 allows a caravan to be coupled to a towing
vehicle without jolting and with millimetric precision. How-
ever, this requires care and a degree of practice.
Following the operating instructions, move the caravan close
to the towing vehicle (apply parking brake and engage gear).
In order to position the caravan precisely, operate the control
knob or slide control until the caravan's coupling is located
precisely over the ball coupling on the towing vehicle. Then
couple the caravan to the vehicle by lowering it at the support
wheel in the usual manner.
Prepare the caravan for towing in the usual way.
The caravan must not be towed with the drive rollers
engaged.

Maintenance

Keep drive elements clear of coarse road dirt. When clean-
ing the caravan, spray the Mover® XT4 with a water hose to
remove mud etc. Make sure that no stones, twigs etc. are
trapped in it. The control unit does not require servicing. The
remote control must be kept in a dry place.
Clean the Mover® XT4 as described above every year (or before
overwintering). Do not park the caravan with the drive rollers engaged.
To prevent the battery from becoming totally discharged dur-
ing long periods of inactivity it must be disconnected and
recharged before using again. Charge the caravan battery
before starting up.
It is extremely easy for you or your caravan dealer to perform
the checking and maintenance of your Mover® XT4 during the
annual inspection of your caravan. If in doubt, please contact
Truma Service or one of our authorised service partners (see
www.truma.com).
19