Operating Instructions; Remote Control; Switching On The Remote Control; Remote Control Led Blink Code And Audio Signal - Truma Mover XT4 Gebrauchsanweisung, Einbauanweisung

Operating instructions

Remote control

Protect the remote control from moisture and direct
sunlight.
LED 1 2 3 4
b
h
i
Figure 2

Switching on the remote control

a = On / Off slide switch
No other remote control function must be active when
the remote control is switched on.
On (LED 4 lights up*)
Off (LED 4 goes off)
* LED 4 flashes for approx. 5 seconds after the remote con-
trol is switched on, until the system is ready for operation.
The following options are available for controlling the caravan:
b using the control knob only
c using the slide control only
b + c using the control knob and the slide control
The caravan symbol on the control knob indicates the current
direction of travel (of the caravan).
The slide control allows the caravan to be moved forwards
and backwards without jerking, with infinitely variable speed
control.
Slide control only
(Forwards, backwards and infinitely variable speed control)
– Push slide control forwards -> caravan moves
forwards (in the direction of the drawbar)
(both wheels rotate forwards)
– Pull slide control backwards-> caravan moves
backwards (in the opposite direction to the drawbar)
(both wheels rotate backwards)
The further the slide control is moved from the zero position,
the faster the speed.
Control knob Mover® XT4
The caravan drawbar can be rotated to the right / left within
a range of approx. 30 cm using the control knob. When the
limit of the rotating range is reached, the rotating procedure is
stopped automatically.
To continue rotating, the caravan must be moved forwards or
backwards in a straight line for a certain distance using the
slide control.
18
Control knob and slide control Mover® XT4
(Caravan right or left and forwards or backwards)
Operating the control knob and the slide control makes the
Mover® XT4 go round in a circle, whereby the wheels rotate
continuously but the inner wheels rotate more slowly than the
outer wheels.
– Turn control knob to right and push slide control forwards ->
caravan drawbar moves to right
left wheel rotates fast – right wheel rotates slowly forwards
– Turn control knob to left and push slide control forwards ->
caravan drawbar moves to left
left wheel rotates slowly – right wheel rotates fast forwards
a
– Turn control knob to right and pull slide control backwards ->
caravan drawbar moves to right
left wheel rotates slowly – right wheel rotates fast backwards
c
– Turn control knob to left and pull slide control backwards ->
caravan drawbar moves to left
h
left wheel rotates fast – right wheel rotates slowly
backwards
i
The further the slide control is pushed forwards the end stop,
the faster the speed (freely selectable turning radius and
speed).
Engaging and disengaging
h = Two-handed operation disengagement of drive rollers
(drive rollers swing away from tyres)
i = Two-handed operation engagement of drive rollers
(drive rollers swing towards tyres)
In order to engage and disengage the drive rollers, both
buttons must always be pressed simultaneously – for
approx. 3 seconds (safety delay) – until the engaging or disen-
gaging of the drive rollers commences.
The buttons can be released when the drive rollers are moving
in the direction of the respective end position. The drive rollers
automatically reach their end position.
If the two buttons for disengaging are pressed whilst the
rollers are engaging, engaging is interrupted, the drive roll-
ers are disengaged and automatically move to their end position.
The remote control switches itself off after about 1 minute if
none of the buttons are pressed. The green LED 4 goes out.
To reactivate the remote control, move slide switch to "Off"
and then back to "On"
There is no "On / Off" switch on the caravan itself.

Remote control LED blink code and audio signal

LED 1 red
LED 2 yellow lights up in the event of a temporary malfunc-
LED 3 red
after approximately 1 second.
indicates state of charge of caravan battery
good LED off
weak LED on
empty LED on and LED 3 indicates
a fault
tion, and an acoustic signal is also emitted
in the event of overcurrent / overtemperature
The power is automatically reduced. Allow
system to cool.
flashes if the Mover® is engaged and the
control unit or the remote control has been
switched off.
lights up in the event of a persistent fault, and
an acoustic signal is also emitted
e.g. in the event of a faulty drive motor
apply the parking brake. See "Troubleshooting"