Stroller Assembly; Stroller Operation - Joie mirus Bedienungsanleitung

!
Pushchair designed to be used from birth shall recom-
mend the use of the most reclined position for new born
babies.
!
For infant child restraints used in conjunction with a
chassis, this vehicle does not replace a cot or a bed.
Should your child need to sleep, then it should be
placed in a suitable pram body, cot, or bed.
!
The parking device shall be engaged when placing and
removing the children.

Stroller Assembly

Please read all the instructions in this manual before assembling and using this product.
Open Stroller
see images 2
2 - 1
Push secondary lock and squeeze one-hand-fold button.
open. Latches should click into place.
!
Check that the stroller is completely open before continuing to use.
Assemble & Detach Front Wheels
see images
3
Assemble front wheels to front legs. Check that wheels are securely attached by pulling on wheel assemblies.
The front wheels can be disassembled by pressing the snap buttons.
Assemble & Detach Storage Basket
see images 4 - 8
Assemble storage basket, plese see images 4
The completely assembled stroller is shown as

Stroller Operation

Adjust Backrest Angle
see images
10
Recline Backrest
There are 4 angles for the backrest.
To recline the backrest, squeeze the recline handle on the back of the seat
- 2
10
To raise the backrest, push up.
!
Make sure the recline is set properly for use.
11
2 - 2
Meanwhile, pull the stroller backward to
-
5 . Detach storage basket, plese see images
9
.
- 1
, pull down on the backrest.
10
Use Armbar
see images
The armbar can be pulled up on both left and right sides.
Press armbar release button
component, and then push down to lock.
Tip
Armbar can be open for easy seating and unseating of child.
Use Buckle
see images
Release Buckle
Press the center button to release the buckle.
Lock Buckle
Match the waist belt buckle with the shoulder buckle
sound means the buckle is locked completely.
!
To avoid serious injury from falling or sliding out, always secure your child with harness.
!
Make sure your child is snugly secured. The space between the child and the shoulder harness is about the
thickness of one hand.
!
Do not cross the shoulder belts. This will cause pressure on child's neck.
Use Shoulder & Waist Harnesses
see images
!
In order to protect your child from falling out, after your child is placed into the seat, check whether the
shoulder and waist harnesses are at proper height and length.
3 - 1
14 Shoulder harness anchor A
- 2
14 Shoulder harness anchor B
- 3
14 Slide adjuster
For larger child, use shoulder harness anchor A and the highest shoulder slots. For smaller child, use shoulder
harness anchor B and the lowest shoulder slots.
Use either shoulder harness anchor in the slots that are closest to child's shoulder height.
-
6 8
Use slide adjuster to change the harness length.
Press the button
Tip
For larger child, use the highest shoulder slots. For smaller child, use the lowest shoulder slots.
Adjust Calf Support
see images
There are three reclining angles, 1-3
To raise calf support, push the calf support from position 1 to position 3.
To lower calf support, press the adjustment buttons on both sides of the calf support
support downwards.
11
- 1
, and then pull up the armbar
11
-
12 13
12
- 1
, and click into the center buckle.
13
- 3
13
-
14 16
- 1
16
- 2
16 , while pulling the waist harness to proper length.
-
17 18
17 for adjustment.
- 2
18
- 2
. Align the armbar end with matching
11
- 2
A click
13
15
- 3
16
17
- 1
, and rotate the calf
18
12