Stroller Assembly - Joie vinca Bedienungsanleitung

Stroller Assembly

(Please refer to figures on page 1-12)
Please read all the instructions in this manual before assembling and using this product.
Open Stroller
see images
-
1 3
Separate storage latch from storage mount , and then lift the handle upwards
1
is open completely .
3
! Check that the stroller is completely latched before continuing to use.
Assemble & Detach Front Wheel
see images
-
4 5
Assemble & Detach Rear Wheel
see images
-
6 8
Assemble Canopy
see images
-
9 10
Assemble & Detach Armbar
see images
-
11
12
The completely assembled stroller is shown as
13
Stroller Operation
Adjust Backrest
see images
-
14 15
There are 5 recline angles for the backrest.
Recline Backrest
To recline the backrest, squeeze the recline handle on the back of the seat, pull down on the backrest.
Raise Backrest
To raise the backrest, push up.
15
! Make sure the recline is set properly for use.
! The maximum load of storage pocket on the back of backrest is 0.45kg.
Use Buckle
see images
-
16 17
Release Buckle
Press the button, the buckle will release automatically.
Lock Buckle
Match the waist belt buckle with the shoulder buckle
can lock
automatically. - 2 A "click" sound means the buckle is locked completely.
17
! To avoid serious injury from falling or sliding out, always
! Make sure your child is snugly secured. The space between the child and the shoulder harness is about the
thickness of one hand.
! Do not cross the shoulder belts. This will cause pressure on a child's neck.
17
, a click sound means the stroller
2
14
16
- 1, and align them with the center buckle, the buckle
17
- 3
17
secure your child with harness.
Use Shoulder & Waist Harnesses
see images
-
18 21
! In order to protect your child from falling out, after your child is placed into the seat, check whether the shoulder
and waist harnesses are at proper height and length.
- 1 Shoulder harness anchor - 2 Slide adjuster
18 18
For larger child, use shoulder harness anchor and the highest shoulder slots. For smaller child, use shoulder
harness anchor and the lowest shoulder slots.
! The position of the shoulder belt anchor can be adjusted from above opening or below pocket.
To adjust the position of the shoulder harness anchor, turn the anchor to be level with the side facing forward.
Thread it through the shoulder harness slot from back to front.
child's shoulder height.
20
Use slide adjuster to change the harness length.
21
Press the button - 2, while pulling the waist harness to proper length.
21
Adjust Calf Support
see images
-
22 23
The calf support has 2 positions.
To raise the calf support, push it upwards. A "click" sound means the calf is locked completely.
22
To lower calf support, press the adjustment buttons on both sides of the calf support
support downwards. - 2
23
Use Front Swivel Lock
see image
24
Front wheel locked or unlocked status as .
24
Tip
It is recommended to use swivel locks on uneven surfaces.
Use Brake
see images
-
25 26
To lock wheels, step the brake lever downwards, the indicator will show red.
To release wheels, step the brake lever downwards again, the indicator will show green.
Tip
Always set the parking brake when stroller is not moving.
Use Canopy
see images
-
27 28
The canopy can be opened or folded, pull it toward front or back.
The canopy can be opened completely to protect your child from the sun uttermostly, just unzip the zip
then pull the canopy toward front.
There is a window on the canopy, through which you can view your baby.
Adjust Handle
see image
29
The handle has 4 positions.
Adjust Seat Height
see images
-
30 31
The seat has 3 positions.
Pull up the seat to increase the seat height.
30
Press the seat height adjustment buttons and pull up, then push down to decrease the seat height.
- 1
19
Rethread it through the slot that is closest to
19
- 1
- 3
21
- 1, and rotate the calf
23
25
26
28
31
, and
27
18