Chapter 2 Setup Using The Setting Menu 2-5 (Gb) - Sony PMS-500P Bedienungsanleitung

Notes
• You can register a subaddress. You can specify a
subaddress by adding an asterisk ( * ) following the
telephone number.
• If you have registered a subaddress, you can call up a
particular Monitoring Codec from a group of ISDN
devices that are bus-connected to the same ISDN line.
All devices on the same ISDN line must have unique
subaddresses.
• The subaddress function may not work properly
depending on types of ISDN networks involved.
• If you have set the ISDN channel as 2B and there is
only one channel available, the connection format
will be the same as the 1B setting.
• When the B1 and B2 channels of the remote site are
the same, you do not have to enter the B2 channel.
• You can use hyphen (–) at any position.
• Sharp (#) is used for macro instruction of the PBX.
• Use an asterisk ( * ) to register a subaddress.
After setting the items, move the cursor to <OK> and
press ENTER. The DIAL LIST menu appears.
(If you selected V.35)
D I A L L I S T # 1
S I T E N A M E :
N E T W O R K : V 3 5
M O D E : 6 4 K
P O R T : D U A L
R A T E : 6 4 K * 2
R S - 3 6 6 : O F F
R E C E I V E P I C T U R E :
< C A N C E L > < O K >
SITE NAME: Displays the remote site name.
NETWORK: Displays the selected interface (V35).
MODE: Select 64K to connect via a normal ISDN
line. Select 56K to connect to specific regions or
countries with a 56Kbps ISDN line speed.
PORT: Select SINGLE to use only the A port. Select
DUAL to use the A and B ports.
If you use data rate greater than 128, you should
only use port A.
RATE: Set the communication speed. This item is
available if you have selected SINGLE for PORT.
If you have selected 56K for MODE, select one of
the following: 56K × 1, 56K × 2, 56K × 3, 56K ×
4, 56K × 5, 56K × 6. If you have selected 64K for
MODE, select one of the following: 64K × 1, 64K
× 2, 64K × 3, 64K × 4, 64K × 5, 64K × 6.
RS-366: Select ON if you use RS-366, otherwise
select OFF.
RECEIVE PICTURE: Select the quality of the
image to be received. Each time you press b , the
selection changes as follows.
FINE n NORMAL n FAST n 4CIF (receive
one still image) n 4CIF...(receive consecutive
still images) n Blank (receive an image with the
remote site setting)
If you have selected ON for RS-366, the following
screen appears.
D I A L L I S T # 1
S I T E N A M E :
N E T W O R K : V 3 5 D U A L
T E L 1 :
[. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .]
[. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .]
T E L 2 :
[. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .]
[. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .]
0 1 2 3 4 5 6 7 8 9 # - * BS
< C A N C E L > < O K >
SITE NAME: Displays the remote site name.
NETWORK: Displays the selected interface (V35)
and PORT/RATE information.
TEL1: Set the B1 channel number.
TEL2: Set the B2 channel number.
After setting the items, move the cursor to <OK> and
press ENTER. The DIAL LIST menu appears.
Note
You cannot register a subaddress. Asterisk ( * ) is used
for macro instruction of the PBX.
(If you have selected HSD)
D I A L L I S T # 1
S I T E N A M E :
N E T W O R K : H S D
C H A N N E L : H S D 6 4 - 1
R E C E I V E P I C T U R E :
< C A N C E L > < O K >
SITE NAME: Displays the remote site name.
NETWORK: Displays the selected interface (HSD).
CHANNEL: Select HSD64-1 to use only the first
channel. Select HSN64-2 to use only the second
channel. Select HSD128 to use both channels.
RECEIVE PICTURE: Select the quality of the
image to be received. Each time you press b, the
selection changes as follows.
FINE n NORMAL n FAST n 4CIF (receive
one stile image) n 4CIF...(receive consecutive
still images) n Blank (receive an image with the
remote site setting)
After setting the items, move the cursor to <OK> and
press ENTER. The DIAL LIST menu appears.
Chapter 2 Setup Using the SETTING Menu
6 4 K * 2
2-5
(GB)