Herunterladen Inhalt Inhalt Diese Seite drucken

Grass Cutting - Stiga MJ 66 Gebrauchsanweisung

Aufsitzmäher (rasenmäher mit fahrersitz mit sitzendem benutzer)
Vorschau ausblenden Andere Handbücher für MJ 66:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 112
Mechanical transmission
Push the pedal down as far as possible (see 
4.11) and move the gear change lever into 
1st gear (see 4.12).
Keep the pedal pressed down and disen-
gage the parking brake. Slowly release 
the pedal which will turn from «brake» to 
«clutch», thus operating the rear wheels (see 
4.11).
WARNING!
The pedal has to be re-
leased gradually, as a sudden engage-
ment may cause the vehicle to tip over 
and the driver to lose control.
Gradually reach the desired speed using 
the throttle and gear lever. To change gear,
press the clutch halfway down (see  4.11).
IMPORTANT   Forward gear must only be 
engaged when the machine has stopped.
    H ydrostatic transmission:
Disengage the parking brake and release 
the brake pedal  (see  4.21).
Press the drive pedal (see 4.22) in direction
«F» and reach the required speed by pro-
gressively increasing pressure on the pedal 
and moving the accelerator.
WARNING!
Drive must be engaged
as described below (see 4.22) to prevent
sudden engagement from causing tipping
up and loss of control of the vehicle, par-
ticularly on slopes.
5.4.3 Braking
Mechanical transmission
To use the brake, press the brake pedal to 
the floor (see 4.11), after reducing speed us-
ing the accelerator so as not to overload the
braking system.
    H ydrostatic transmission
First reduce the machine's speed by reduc-
ing the engine's r.p.m., and then press the 
brake pedal (see 4.21) to slow down the ma-
chine until it stops.
The machine already slows down consider-
ably by just releasing the drive pedal.
5.4.4 Reverse
IMPORTANT   Reverse must only be engaged 
when the machine has stopped.
IMPORTANT To proceed in reverse gear with
the cutting means engaged, it is necessary to 
press and hold the consent pedal down (see 4.7)
so as not to cause the engine to stop.
Mechanical transmission
Press the pedal until the machine stops and 
then switch into reverse by shifting the lever 
sideways and into position «R»  (see  4.12). 
Gradually release the pedal to engage the 
clutch and then begin moving in reverse.
    H ydrostatic transmission:
When the machine is stopped, start the re-
verse movement by pressing the drive pedal 
in the «R» direction (see 4.22).

5.4.5 Grass cutting

To start cutting:
–  move the throttle to «FAST»;
–    b ring the cutting-means assembly to the high-
est position;
–    l et the engine warm up a few minutes before 
engaging the cutting means;
–    e ngage the cutting means (see 4.3) only on 
short grass lawns; avoid engaging them on 
stony ground or when the grass is very high;
IMPORTANT If the cutting means are
engaged when the grass is too high, the
engine could suffer a sudden drop of r.p.m.
and stop in some cases, or the clutch may be 
worn.
–    s tart moving forwards on the grass very 
slowly and with utmost caution, as already 
described;
– regulate the cutting height and speed (see
4.4) considering the conditions of the lawn 
(the height, density and dampness of the 
grass).
Mechanical transmission
–    H igh and dense grass – wet lawn:
1st gear
–    L ow grass – dry lawn: 2nd 3rd gear
NOTE The fourth gear is just a transfer
gear to be used on the flat.
EN - 11

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis