USE OF THE SCALE
The product is equipped with a scale for food
incorporated
IMPORTANT:
when using the scale with pots or containers larger than Ø
20cm, it is advisable to switch off the suction of the hood in
order to avoid affecting the measurement of the weight;
NOTE = The pot or container must always be centred on the
weighing area, avoiding to obstruct the suction area.
NOTE = the maximum load of the scale is 10KG; consider a
tolerance of +/-2g on the value of each individual weighing.
Operation
Switch-on
To activate the scale tap the weighing area (16) or place the
product to be weighed on the area itself;
the display (22) activates showing a weight equal to zero or
equal to the weight of the product
NOTE = if in the weighing area are already present products
and these are removed, the scale will activate showing the
weight of the product removed with a negative sign;
vice versa, if you add other products, the scale will
activate showing only the weight of the last product added
Switching off
The scale switches off automatically:
- after 2 minutes, if there are no objects on the weighing area
- after 8 minutes, if there are objects on the weighing area
UNIT function
The scale is set by default on the metric measurement
system, in grams;
press "UNIT" (20) to change the unit of measurement;
the unit of measurement in use is displayed below the display
of the scale, in the display (24)
ZERO function
The function 'ZERO' (19) allows to bring "to zero" the numeric
display of the scale, whether there are products in the
weighing area or not (15);
NOTE = the indicator ZERO (23) goes off when products are
added or removed from the weighing area (and the weight of
the products will be shown);
TARE function
The function "TARE" (18) allows to gradually weigh different
foods without having to remove them from the weighing area,
and be able to have both the weight of each single food that
total weight
use:
- position the first product in the weighing area, the display
(22) displays the weight "1"
- press "TARE" (18), the weight in the display (22) is reset
- add another product in the weighing area, the display (22)
displays the weight "2"
- press again "TARE" (18) the display (22) displays the
weight "1" + the weight "2"
NOTE = it is possible to add products up to the maximum load
of the scale
NOTE = to exclude the weight of container from the total
weight, carry out initially the tare through the "ZERO" (19)
function
NOTE= to exit from the function "TARE" press "ZERO" (19)
HOLD function
The function "HOLD" (17) allows to store the weight that you
are viewing and then recall it to add it or subtract it from the
new weight on the scales; the weight will remain stored in
memory until the scale is switched off
use:
- place the product in the weighing area
- keep pressed "HOLD" (17) until the weight in the display
starts to flash: the value has been stored
NOTE = you may proceed by removing the weight from the
scale and use it in all its functions
NOTE = repeat a new long pressure to store a new weight;
only the last weight saved will remain in the memory.
By pressing "HOLD" (17) at any time you can view the value
stored, it appears and flashes for a few seconds in the display
(23);
within this time by pressing "HOLD" (17) again the stored
weight is added to the weight on the scales;
the display (23) displays the total value and the bright
feedback "HOLD" (23) remains alight, to inform that the
function is still active.
by pressing "HOLD" (17) again the weight stored is
subtracted from the weight shown in the display;
the display (23) displays the value of the difference and it
exits automatically from the function.
Example:
- weight stored: 1KG
- weight on the scale when calling the function: 2KG
- weight "added", that appears in the display: 3KG (1KG+2KG)
- weight "subtracted" before exiting the function: 2KG (3KG -
1KG)+
35