Assembly; Fitting The Lower Brace (02, 03); Fitting The Operating Panel (04); Fitting And Adjusting The Bowden Ca - AL-KO SnowLine 620 E III Betriebsanleitung

GB
■
Never fill the fuel tank while the engine is run-
ning or hot.
■
Never over-fill the fuel tank (petrol expands).
■
Always screw on the fuel tank cap tightly.
■
Replace a damaged fuel tank or fuel tank
cap.
■
Never eat, drink or smoke when filling the ap-
pliance with petrol or oil.
■
If petrol has leaked out:
■
Do not start the engine.
■
Avoid start attempts.
■
Pick up leaked petrol using a binding
agent or cloth and dispose of in the prop-
er manner.
■
Clean the appliance.
■
If engine oil has leaked out:
■
Do not start the engine.
■
Pick up leaked oil using an oil binding
agent or cloth and dispose of in the prop-
er manner.
■
Clean the appliance.

4 ASSEMBLY

WARNING! Danger if assembly is not
carried out completely! Operation of an incom-
pletely assembled appliance can result in serious
injury.
■
Operate the device only when it is fully as-
sembled!
■
Before switching on, check that all safety and
protective devices are in place and function-
ing correctly!
Necessary tools
No. Tool
1 Open-end or ring spanner WAF 10 (x2)
2 Open-end or ring spanner WAF 13
3 5 mm Allen key
4 Combination or long-nose pliers
5 Screwdriver
6 Spray oil
7 Tyre pump with pressure gauge (car tyre
valve)
4.1

Fitting the lower brace (02, 03)

1. Loosen the bolts on the snow blower (02/1).
30
2. Attach the lower brace to the snow blower
(03/1).
4.2

Fitting the operating panel (04)

1. Tighten the 3 bolts (04/1).
2. Leave the hole (04/2) free for the guide of the
hand crank.
4.3 Fitting and adjusting the Bowden cables
(travel and auger drive) (05)
Adjust the 3 Bowden cables as follows:
1. Turn the adjuster on the Bowden cable (05/1)
in the direction of the arrow (05/a) until the
Bowden cable no longer sags (is slightly ten-
sioned). While turning the adjuster, hold the
cable so that it does not become twisted.
2. Tighten lock nut (05/2) (05/b).
4.4

Fitting the gear lever linkage (06)

1. Hook the linkage (06/1) into the housing
(06/2) at the bottom.
4.5 Fitting the levers for gear selection and
discharge height (07)
1. Push spring washers (07/1) onto the thread.
2. Screw on and tighten the discharge height le-
ver (07/2).
3. Screw on and tighten the gear selection lever
(07/3).
4.6 Connecting the heater and lighting plug
(08)
1. Connect the heater and lighting plug (08/1).
4.7 Fitting the snow discharge spout (09,
10)
1. Apply spray oil (or grease) to the sliding sur-
face (09/1) of the snow discharge spout on
the snow blower.
2. Fit the snow discharge spout (10/1) (10/a).
3. Insert the mounting bolts (10/2) through the
brackets and snow discharge spout from the
inside.
4. Secure the snow discharge spout with the
self-locking nuts (10/3).
4.8 Connecting the Bowden cable to the
discharge flap (11)
1. Hook the Bowden cable into the guide (11/1,
11/2). The rubber sheath must be attached to
the outer Bowden cable.
2. Tighten lock nuts (11/3, 11/4) securely
against the guide (11/2).
Assembly