Assembling The Extension Attachment; Fitting/Removing The Protective Guard; Installing/Replacing The Cutting Blade; Installing/Replacing The Strimmer - Parkside PBK 4 A2 Originalbetriebsanleitung

Assembling the extension attachment

ATTENTION!
■ Do not use the extension attachment/boom
the 3-tooth cutting blade/strimmer attachment!
NOTE
► Use the extension attachment/boom
heights.
♦ Fit the extension attachment/boom
the hedge trimmer or the pole pruner. The assembly is carried out in
the same manner as previously described for the attachments.

Fitting/removing the protective guard

WARNING!
■ When working with the 3-tooth cutting blade
guard must be fitted. The protective guard
the metal panel of the boom
be attached to the front boom
hex key to do this (see fig. 2a–2c).
Cutting equipment
3-tooth cutting blade
Strimmer
WARNING!
► Do not use any other cutting equipment apart from that which is
supplied with the product. The use of any other cutting equipment
or protective equipment is deemed to be improper and carries a
significant risk of accidents.

Installing/replacing the cutting blade

■ Fit/remove the 3-tooth cutting blade
ATTENTION! Left-hand thread!
■ Find the hole in the drive plate
block it with the supplied hex key
■ Place the 3-tooth cutting blade
The inscription must be visible from above when holding the tool in the
working position (see fold-out page). Both sides of the 3-tooth cutting
blade can be used.
■ Fit the pressure plate over the thread on the splined shaft (see Fig. 1c).
■ Fit the pressure plate cover
■ Tighten the nut with the spark plug wrench
ATTENTION! Left-hand thread! (see Fig. 1f).
■ The 3-tooth cutting blade is fitted with a plastic cover on delivery. It
must be removed before use and refitted during periods when the tool
is not in use.
■ The plastic cover can now be removed.
ATTENTION! SHARP EDGES, WEAR PROTECTIVE GLOVES!
■ Fit the cutting filament protective guard
■ The cutting filament protective guard
with the cutting filament. The cutting filament protective guard
(pre-fitted on delivery) is fitted as shown in figure 2a.
■ Ensure that the cutting filament protective guard
into place. There is a blade A
protective guard C . It is protected with a safety cover
and 2b).
B
■ Remove the safety cover before starting work and replace it after
finishing work.
PBK 4 A2
in combination with
for working at greater
between the engine unit and
, the protective
is positioned under
. The protective guard can now
with 4 screws . Use the supplied
Protective equipment
Protective guard
Protective guard + cutting filament
protective guard C
as shown in figures 1a–1f.
, align it with the adjacent hole and
.
on the drive plate (see Fig. 1b).
(see Fig. 1d).
anticlockwise.
C on the protective guard
C
must be fitted when working
C
C is correctly clicked
on the inside of the cutting filament
B (see Figs. 2a
ATTENTION! SHARP EDGES, WEAR PROTECTIVE GLOVES!
■ To remove the cutting filament protective guard
guard , take a tool, such as a screwdriver, to carefully remove the
three mounting pins.
ATTENTION! RISK OF INJURY!

Installing/replacing the strimmer

■ Install/replace the strimmer
ATTENTION! Left-hand thread!
■ Find the hole in the drive plate
block it with the supplied hex key
■ Screw the strimmer anticlockwise onto the thread.

Putting on the carrying harness

NOTE
■ The following adjustments can be made to make sure that you can
work without becoming fatigued. The settings may vary depending
on your body size.
■ Before starting work, adjust the carrying harness
size.
■ Balance the tool with the fitted cutting tool so that the cutting tool
swings just above the ground without the need to move the tool with
your hands.
1.) Put on the carrying harness
place (see Fig. 3a).
2.) As shown in figure 3b, pull on the belt
harness centrally on your body and adjust the upper body size
as required.
3.) To tighten the two shoulder straps, pull on the two shoulder straps as
shown in figure 3c.
4.) To ensure to the correct position of the tool on the carrying harness,
pull the belt as shown in figure 3d.
5.) Hook in the carabiner
strap on the quick release mechanism.
6.) Now take the tool and hang it so that the carrying lug
carabiner as shown in figure 3h. The carrying lug
moved by loosening the screw
orientation of the tool.

Setting the cutting height

■ Put on the carrying harness
on the carrying harness").
■ Use the various adjusting straps on the carrying harness
the optimum working and cutting position (see section "Putting on the
carrying harness").
■ Perform a few circular movements without starting the engine in order
to find the ideal carrying strap length (see Fig. 5a).
■ The carrying harness
Pull on the red strap if you have to release the tool quickly (see Fig. 3i).
.
ATTENTION!
■ Always use the carrying harness
on the carrying harness
and it is idling. Switch off the engine before removing the carrying
harness .
C
from the protective
as shown in figure 2c.
, align it with the adjacent hole and
.
to fit your body
and close the clasp so that it clicks into
to position the carrying
(see Figs. 3e–3g) and secure it with the red
can also be
and sliding it to achieve optimum
and hook the tool (see section "Putting
is equipped with a quick release mechanism.
when working with the tool. Put
as soon as you have started the engine
GB │ CY │
clicks into the
to adjust
11 ■