Trouble Shooting Chart; Service Department, Spellbrook, Bishop's Stortford, Hertfordshire. Cm23 4Bu; Murray, Inc - Murray 624505x54B Betriebsanleitung

2. Let the engine run until it is out of gasoline.
3. Drain the oil from the warm engine. Fill the
engine crankcase with new oil.
4. Remove the spark plug from the cylinder.
Pour one ounce of oil into the cylinder. Slow-
ly pull the recoil–start grip so that the oil will
protect the cylinder. Install a new spark plug
in the cylinder.
5. Thoroughly clean the snow thrower.
6. Lubricate all lubrication points. See the Main-
tenance section.
7. Be sure that all nuts, bolts and screws are
securely fastened. Inspect all visible moving
parts for damage, breakage and wear. Re-
place if necessary.
8. Cover the bare metal parts of the blower
housing, auger, and the impeller with spray
rust preventative lubricant.
9. Put the unit in a building that has good ven-
tilation.
10. If the machine must be stored outdoors,
block up the snow thrower to be sure the en-
tire machine is off the ground.
TROUBLE
Difficult starting
Engine runs erratic
Engine stalls
Engine runs erratic;
Loss of power
Excessive vibration
Unit fails to propel itself
Unit fails to discharge snow
F–001080J
11. Cover the snow thrower with a suitable pro-
tective cover that does not retain moisture.
Do not use plastic.
How To Order Replacement Parts
The replacement parts are shown either on the
back pages of this Instruction Book or in a
separate Parts List Book.
Use only manufacturer's authorized or approved
replacement parts. The letter placed on the end
of the part number denotes the type of finish for
the part, C for chrome, Z for zinc, a PA for
purchased assembly. It is important that you
include this when ordering a part. Do not use
attachments or accessories not specifically
recommended for this unit. In order to obtain
proper replacement parts you must supply the
model number (see nameplate).
Replacement parts, except for the engine,
transmission, transaxle or differential, are
available from the store where the product was
purchased, a service shop recommended by the
store or from a "Murray, Inc. Central Parts
Distributor" listed on the back page of this
Instruction Book.

TROUBLE SHOOTING CHART

CAUSE
Defective spark plug.
Water or dirt in fuel system.
Blocked fuel line, empty gas tank, or stale
gasoline
Unit running on CHOKE.
Water or dirt in fuel system.
Loose parts: damaged impeller
Drive belt loose or damaged.
Incorrect adjustment of traction drive cable
Worn or damaged friction wheel.
Auger drive belt loose or damaged.
Auger control cable not adjusted correctly.
Shear bolt broken
Discharge chute clogged.
Foreign object lodged in auger
16
If you are unable to obtain parts or service in the
manner outlined above, then contact:
HAYTER LIMITED,
Service Department,
Spellbrook,
Bishop's Stortford,
Hertfordshire. CM23 4BU.

MURRAY, INC.

Outdoor Power Equipment
Customer Service Department
P.O. Box 268
Brentwood, Tennessee U.S.A. 37027
1–800–251–8007 Collect telephone calls will not
be accepted.
Replacement parts for the engine, transaxle, or
transmission, are available from the
manufacturer's authorized service centre found
in the yellow pages of the telephone directory.
Also, see the individual engine or transmission
warranties to order replacement parts.
When ordering the following information is
required:
(1) The Model Number
(2) Serial Number
(3) Part Number
(4) Quantity
CORRECTION
Replace spark plug.
Use carburetor bowl drain to flush and refill with
fresh fuel.
Clean fuel line; check fuel supply; add fresh
gasoline
Set choke lever to RUN position.
Use carburetor bowl drain to flush and refill with
fresh fuel.
Stop engine immediately and disconnect spark
plug wire. Tighten all bolts and make all
necessary repairs. If vibration continues, have
the unit serviced by a competent repairman.
Replace drive belt.
Adjust traction drive cable.
Replace friction wheel.
Adjust auger drive belt; replace if damaged.
Adjust auger control cable.
Replace shear bolt
Stop engine immediately and disconnect spark
plug wire. Clean discharge chute and inside of
auger housing.
Stop engine immediately and disconnect spark
plug wire. Remove object from auger.
ENGLISH