Bosch Intuvia Serie Originalbetriebsanleitung Seite 18

English–4
Interaction of the eBike System with the Bicycle Gears
The bicycle gears should be used as with a normal bicycle,
even with eBike motor assistance (please observe the operat-
ing instructions of your eBike).
Independent of the type of gearing, it is recommended to
briefly interrupt the pedaling while changing gears. This
makes changing gears easier and reduces the wear of the
drive train.
By selecting the right gear, you can increase the speed and
range with the same pedaling effort.
For this reason, follow the shift recommendations provided
by indications g and h on your display. If indication g is dis-
played, you should shift to a higher gear with lower cadence.
If indication h is displayed, you should select a lower gear with
higher cadence.
Switching bike lights on/off
In the model in which the lighting is powered by the eBike sys-
tem, the front and rear lights can be switched on and off at the
same time via the on-board computer with button 2.
When the lighting is switched on "Lights on" appears and when
the lighting is switched off "Lights off" appears for approx. 1 s
in text indication d. The lighting symbol c is displayed when the
light is on.
Switching the bike light on and off has no effect on the back
lighting of the display.
Switching the Push-assistance mode On/Off
The push-assistance feature makes it easier to push the
eBike. The speed in this function depends on the set gear and
cannot exceed 6 km/h (max.). The lower the set gear, the low-
er the speed in the push-assistance function (at full output).
 The push-assistance function may only be used when
pushing the eBike. Danger of injury when the wheels of
the eBike do not have ground contact while using the push-
assistance function.
To activate the push-assistance function, briefly press but-
ton "WALK" on your on-board computer. After activation,
press button "+" within 3 s and keep it pressed. The eBike
drive is switched on.
Note: The push assistance cannot be activated in the "OFF"
assistance level.
The push assistance is switched off as soon as one of the fol-
lowing occurs:
– you release button "+" 12,
– the wheels of the eBike are blocked (e.g. by actuating the
brakes or impacting against an obstacle),
– the speed exceeds 6 km/h.
Note: On some systems the push-assistance function can be
started directly by pressing the "WALK" button.
34
1 270 020 XBI | (11.4.16)
Displays and configurations of the on-board
computer
Speed and Distance Indication
The speed indication f always displays the current speed.
The following functions are available in the function indica-
tion (combination of text indication d and value indication e):
– "Clock": Current time
– "Max. speed": Maximum speed achieved since the last
reset
– "Avg. speed": Average speed achieved since the last reset
– "Trip time": Trip time since the last reset
– "Range": Estimated range of the available battery-pack
charge (for constant conditions such as assistance level,
route profile, etc.)
– "Odometer": Display of the total distance travelled with
the eBike (cannot be reset)
– " NuVinci Cadence/Gear": This menu item is displayed
only in conjunction with a Nu Vinci H|Sync automatic trans-
mission.
If you press the "i" button for longer than 1 s, you will
access the NuVinci menu item from any menu item in the
information menu.
To switch from the " NuVinci Cadence" mode to the
" NuVinci Gear" mode, press the "i" button for 1 s.
To switch from the " NuVinci Gear" mode to the
" NuVinci Cadence" mode, all you have to do is briefly
press the "i" button.
The default setting is " NuVinci Cadence".
Range Odometer NuVinci Cadence
(1 s)
(1 s)
NuVinci Gear
– "Gear": This menu item appears only in conjunction with a
Shimano Di2 gear hub. The currently engaged gear of the
transmission is shown on the display. The newly engaged
gear will be shown briefly on the display whenever the gear
is shifted.
– " Gear: Auto": This menu item appears only in conjunc-
tion with an SRAM automatic transmission.
Range Odometer Gear: Auto
(1 s)
(1 s)
Gear
By pressing the "i" button for more than 1 s, you can
switch back and forth between the " Gear: Auto" auto-
matic mode and the " Gear" manual mode.
Bosch eBike Systems
If you are in first gear in manual mode, you can also press
the "–" 11 button to go to the " Gear: Auto" mode. By
pressing the "–" 11 button again, you can switch back to
the manual mode. It is also possible to access the manual
mode by pressing the "+" 12 button.
– "Trip distance": Distance covered since the last reset
To switch between display functions, press button "i" 1 on
the on-board computer or button "i" 10 on the operating unit
repeatedly until the required function is displayed.
To reset "Trip distance", "Trip time" and "Avg. speed",
switch to any of the three functions and then press and hold
the "RESET" button 6 until the indication is set to zero. This
also resets the values of the other two functions.
To reset the "Max. speed", switch to this function and then
press and hold the "RESET" button 6 until the indication is set
to zero.
To reset "Range", switch to this function and then press the
"RESET" 6 button until the display is reset to the value of the
factory setting.
If the on-board computer is removed from the holder 4, all val-
ues of the features are saved and can still be displayed.
Displaying/Adapting Basic Settings
The basic settings can be displayed and changed regardless
of whether the on-board computer is inserted in the holder 4
or not. Some settings are visible and changeable only when
the operating computer is inserted. Some menu items may be
missing depending on the equipment of your eBike.
To access the basic settings menu, press and hold the
"RESET" button 6 and the "i" button 1 until "Configuration"
is displayed in text indication d.
To switch between the basic settings, press button "i" 1 on
the on-board computer repeatedly until the required basic
setting is displayed. If the on-board computer is inserted in
the holder 4, you can also press button "i" 10 on the operat-
ing unit.
To change the basic settings, press the On/Off button 5 next
to indication "–" to reduce or scroll down, or the lighting but-
ton 2 next to indication "+" to increase or scroll up.
If the on-board computer is inserted in the holder 4, it is also
possible to change using buttons "–" 11 and "+" 12 on the
operating unit.
To exit the function and save a changed setting, press the
"RESET" button 6 for 3 s.
The following basic settings are available:
– "– Clock +": The current time can be set here. Pressing
(1 s) and holding the setting buttons fast-forwards the setting
speed.
– "– Wheel circum. +": You can change this value pre-set by
the manufacturer by ± 5 %. This menu item is displayed on-
ly when the on-board computer is in the holder.
– "– English +": You can change the language of the text indi-
cations. You can choose between German, English, French,
Spanish, Italian, Portuguese, Swedish, Dutch and Danish.
Bosch eBike Systems
English–5
– "– Unit km/mi +": The speed and distance can be dis-
played either in kilometres or miles.
– "– Time format +": The time can be displayed either in the
12 hour or 24 hour format.
– "– Shift recom. on/off +": You can switch the indication
of a shift recommendation on and off.
– "Power-on hours": Indicates the total travel duration with
the eBike (not changeable).
– "Gear calibration" (only NuVinci H|Sync): Here you can
calibrate the continuously variable transmission. Confirm
the calibration by pressing the "Bike lights" button. Then
follow the instructions.
In the event of an error, it can also be necessary to perform
calibration when riding. In this case, you also confirm the
calibration by pressing the "Bike lights" button and then
follow the instructions on the display.
This menu item is displayed only when the on-board com-
puter is in the holder.
– "– Start gear +": The starting gear can be set here. The au-
tomatic shift-back function is switched off in the "––" posi-
tion. This menu item is displayed only in connection with
SRAM DD3 Pulse and Shimano Di2. This menu item is dis-
played only when the on-board computer is in the holder.
– "Gear adjustment": This menu item can be used to per-
form fine adjustment of the Shimano Di2. The pre-defined
adjustment range can be found in the operating instruc-
tions provided by the transmission manufacturer. Perform
fine adjustment as soon as you hear unusual sounds com-
ing from the transmission. This will prevent premature
wear of the transmission and also avoid any impairments in
gear shifting behaviour which could cause you to fall in ad-
verse situations. This menu item is displayed only in con-
junction with Shimano Di2. This menu item is displayed
only when the on-board computer is in the holder.
– "Displ. vx.x.x.x": This is the software version of the display.
– "DU vx.x.x.x": This is the software version of the drive
unit. This menu item is displayed only when the on-board
computer is in the holder.
– "DU # xxxxxxxxx": This is the serial number of the drive
unit. This menu item is displayed only when the on-board
computer is in the holder.
– " Service MM/YYYY": This menu item is displayed
when the bike manufacturer has set a fixed service ap-
pointment.
– " Serv. xx km/mi": This menu item is displayed when
the bike manufacturer has set a fixed service appointment
after a certain mileage has been reached.
– "Bat. vx.x.x.x": This is the software version of the battery
pack. This menu item is displayed only when the on-board
computer is in the holder.
– "1. Bat. vx.x.x.x": When using 2 battery packs this is the
software version of one of the battery packs. This menu
item is displayed only when the on-board computer is in
the holder.
1 270 020 XBI | (11.4.16)
35