Herunterladen Inhalt Inhalt Diese Seite drucken

Flame Baffle Plate; Door Adjustment - Dik Geurts Instyle 700EA Installationsvorschrift

Vorschau ausblenden Andere Handbücher für Instyle 700EA:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

I N STA L L A TI O N MA N U A L
The bottom plates and the underlying felt are first removed and the rear plates last. The insertion of the
vermiculite plates takes place in reverse order.
Make sure that the vermiculite plates are replaced in the original position! The back plate with the small, not
!Caution
countersunk, holes must be placed to the front.

9.2.2 Flame baffle plate

On delivery the flame baffle plate (see Appendix 2, Fig. 8) is laying on the bottom of the appliance. It must be laid
in the top of the appliance.
To do this proceed as follows:
Ø
Take the flame baffle plate and tilt it to the right.
The stainless steel profile must be placed at the front with the screw heads facing the top (see Appendix 2, fig. 8).
!Caution
Ø
Lift the flame baffle plate into the top of the appliance.
Ø
Slide the left-hand side of the flame baffle plate over the edge.
Ø
Now lift the right-hand side up and slide the flame baffle plate to the right, so the right-hand side falls over the
right edge.
Ø
Centre the flame baffle plate as far as possible to the back in the appliance.
Ø
The flame baffle plate is now in the correct place.

9.3 Door adjustment

Check the closing of the door with installation or maintenance. The door can be adjusted if desired. This is the
case if sealing is insufficient is (gaps).
Ø
Check the sealing of the door by placing a sheet of paper between the door and the fire. After closing the door the
sheet of paper may not be able to be easily pulled out. Check around the door.
Proceed as follows when adjusting the door:
Ø
Loosen the 2 hexagonal bolts on the top and bottom side of the hinging part of the door with an open-end
spanner one turn (see Appendix 2, Fig. 9).
Do not fully remove these bolts!
!Caution
Ø
The door can now be adjusted.
Ø
Check whether the door still seals well using the test with a sheet of paper described above.
Ø
Tighten the bolts again.
Does the door still not seal properly?
Ø
Replace the sealing cord (see Appendix 2, Fig. 10).
Ø
Adjust the door handle.
When replacing the cord proceed as follows:
Ø
Open the door.
Ø
Remove the cord and the mastic from the recess.
Ø
Apply a new layer of high temperature-resistant mastic in the recess where the cord was.
Ø
Place a new cord in the recess. Do this loosely and do not pull the cord tight.
Ø
Insert both ends of the cord in the special sleeve.
The cord, the sleeve and the mastic are available through your supplier.
Make sure that the sleeve is placed on the underside of the glass pane.
!Caution
The door can also be adjusted in height. There are 2 eyelets on the upper pin on which the door is hung.
Removing one or more of these eyelets allows the door to fall to the desired level.
Proceed as follows when adjusting the door handle:
Ø
Loosen the 2 hexagonal pin nuts around which the handle of the door falls a few turns (see Appendix 2, fig. 11).
This pin ensures that the door is tightly clamped.
Ø
Adjust the pin.
Ø
Tighten the 2 hexagonal nuts again.
Ø
Test the sealing of the door (see the start of this paragraph).
Ø
Repeat this process if the result is not satisfactory.
UK

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Prostyle 700ea

Inhaltsverzeichnis