Black & Decker FSM1640 Originalanweisungen Seite 8

ENGLISH
Attaching the handle (Fig. A)
Slide the bottom end of the handle (4) into the top end of
u
the steam mop body (13) until it clicks into place.
Attaching the steam head (Fig. B)
Slide the bottom end of the steam mop body (13) onto the
u
steam head (5) until it clicks into place.
The steam head can be removed from the Steam mop
u
body by pressing the steam head release button (14) and
pulling the steam mop body (13) off the steam head (5).
Attaching the water jug (Fig. C)
Clip the water jug (3) onto the handle (4).
u
Slide the water jug (3) down into the Steam mop body
u
(13), ensure that the water jug is firmly seated.
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your
BLACK+DECKER dealer:- (cat. no. FSMP20-XJ).
Steam head cleaning pad - cat. no. FSMP20-XJ).
Delta head cleaning pad - cat. no. FSMP30-XJ (FSM1630
Only).
Place a cleaning pad (6 or 7) on the floor with the 'hook &
u
loop' side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(6 or 7).
Caution! Always place your steam mop on the resting mat (8)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (4) to the upright position and turn the
u
steam mop 'OFF'.
Place the steam mop on the resting mat and wait until it
u
cools down. (approximately five minutes)
Place the front of your shoe onto the cleaning pad removal
u
tab (15) and press down firmly.
Lift the steam mop up off the cleaning pad.
u
Caution! Always place the steam mop on the resting mat (8)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Attaching the carpet glider (Fig. F)
Place carpet glider on the floor.
u
Lightly press the steam mop down onto the carpet glider
u
(9) until it clicks into place.
Caution! Always place the steam mop on the resting mat (8)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
8
(Original instructions)
Removing the carpet glider (Fig. F)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (4) to the upright position and turn the
u
steam mop 'OFF'.
Place the steam mop on the resting mat and wait until it
u
cools down. (approximately five minutes)
Place the front of your shoe onto the carpet glider removal
u
tab (16) and press down firmly.
Lift the steam mop up off the carpet glider (9).
u
Caution! Always place the steam mop on the resting mat (8)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
The Delta Head (Fig. G)
This Steam Mop incorporates a built in delta head which
enables you to access into tight corners and narrow gaps.
Caution! Always wear suitable shoes when accessing the
delta head on your steam mop. Do not wear slippers or open
toed footwear.
Return the handle (4) to the upright position and turn the
u
steam mop 'OFF'.
Place the steam mop on the resting mat and wait until it
u
cools down. (approximately five minutes)
Place the front of your shoe onto the steam head removal
u
tab (18) and press down gently.
Lift the delta head (17) up off the steam head (5).
u
Fit the delta head cleaning pad to the bottom of the delta
u
head.
Note: Remove the cleaning pad before re-fitting the delta
head to the steam head.
To refit the delta head, place the tip of the delta head into
u
the steam head then press down firmly ensuring that the
delta head clicks into place.
Caution! Always place the steam mop on the resting mat (8)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Filling the water tank (Fig. H)
The watertank on your steam mop is removable for convieni-
ent and easy filling.
This Steam Mop incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
Remove the water tank (3).
u
Open the filler cap (19) by pressing the release button
u
(20).
Fill the water tank (3) with water.
u
Warning! Your water tank has a 0.5 litre capacity. Do not over
fill the tank.