Description Of Components; Preparation; Raise The Guide Bar (Figure A1 + B1 + V4 ); Support Bar Assembly (Figure W2 + D1 ) - Sabo 52-S A Betriebsanleitung

Maintenance and cleaning work may only be carried out on level
surfaces with the engine switched off and the spark plug connector
disconnected. Regular maintenance is essential for safety and top
performance.
Pos: 11.9.1 3 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Kerzen stecke r niema ls bei laufendem Mo tor ab ziehen @ 13\mod _12 8021 905 695 6_6.do cx @ 1 1007 3 @ @ 1
• Never remove the plug connector when the engine is running! Risk of electric
shock.
Pos: 11.9.1 4 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Kerzenste cker n ur be i abgeküh ltem Moto r abz iehen @ 53\mod_ 151 300 1243 580 _6.do cx @ 57 7230 @ @ 1
• Only remove the plug connector once the engine has cooled down. Risk of
burns!
Pos: 11.9.1 5 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Auf fe sten Sit z des Zündke rze nstecke rs a chten @ 53\mod _151 300 352 3258 _6.do cx @ 57 725 8 @ @ 1
• Make sure the spark plug connector is fitted tightly. Risk of electric shock.
Pos: 11.9.1 6 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Tank nu r im Fre ien ent leeren @ 0\mod_ 111 5186 486 750 _6.docx @ 267 @ @ 1
• If the tank has to be emptied, this should be done in the open, and with a cold
engine. Take care to ensure that no fuel is spilt.
Pos: 11.9.1 7 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Nu r Origi nalersatzteile ve rwenden SABO+JD @ 2 6\mod_1 3771 684 882 08_6. docx @ 1 875 31 @ @ 1
For reasons of warranty and safety, only genuine spare parts may be used.
Non-equivalent spare parts can damage the machine and are a safety hazard.
Pos: 12.1 /---------- 1 Leerzeile ---------- @ 0\mod_111 461 1787 140 _6.do cx @ 41 @ @ 1
Pos: 12.2 /Innente il/Be sch reib ung de r Ba uteile/1 BE SCHRE IBUNG DER BAUT EILE @ 0\mo d_11 151 878 9246 8_6. docx @ 2 71 @ 1 @ 1

7 DESCRIPTION OF COMPONENTS

Pos: 12.3 /Innente il/Be sch reib ung de r Ba uteile/5 2-S A @ 5 6\mod_1 542 273 6359 81_ 0.docx @ 594 106 @ @ 1
Pos: 12.4 /Innente il/Be sch reib ung de r Ba uteile/ Bil d 52- S A_SA2 1201 9 @ 5 5\mod_1 542 2068 233 48_0 .docx @ 5936 86 @ @ 1
Pos: 12.5 /Innente il/Be sch reib ung de r Ba uteile/ Bes chre ibun g der Baute ile 52- S A Schnel lspan ner Text @ 44\mod _14 6900 524 819 6_6.do cx @ 50 386 5 @ @ 1
1 Engine stop safety control bar
2 Drive control bar
3 Support bar
4 Oil filling nozzle with dipstick
5 Engine cover
6 Exhaust protection grill
7 Spark plug
8 Cutting height adjustment
9 Baffle plate
10 Air filter
11 Belt drive covers
12 Tank cap
13 Quick-release clamp
14 Starter cable grip
Pos: 12.6 /Innente il/Be sch reib ung de r Ba uteile/5 2-PRO S A @ 56\mod_ 154 227 3666 356 _0.do cx @ 59 4134 @ @ 1
Pos: 13.1 /---------- 1 Leerzeile ---------- @ 0\mod_111 461 1787 140 _6.do cx @ 41 @ @ 1
Pos: 13.2 /Innente il/Vo rbe reiten de Arbei ten/1 VOR BEREITEND E AR BE ITEN @ 0\mod_ 1115 194 917 734_ 6.docx @ 291 @ 1 @ 1

8 PREPARATION

Pos: 13.3 /Innente il/Vo rbe reiten de Arbei ten/Vo rbe reiten de Arbeite n Text 52e r Seitena uswu rf SABO Ho lm vormo ntie rt @ 38\mod_ 143 9449 589 498 _6.docx @ 404 406 @ @ 1
The following parts are included in the packaging for assembly of the mower:
• Mower with preassembled guide bar and support bar
• Baffle plate
• Tool bag with the following contents:
– Operating instructions with declaration of conformity
– Warranty conditions
– Various fixing parts.
In the unlikely event of a missing part, please contact your dealer.
Pos: 13.4 /Innente il/Vo rbe reiten de Arbei ten/Vo r Monta ge... Holm und... Sta rterseil halte r... Zündke rzen stecke r abz iehen! H inweis @ 32\mod _14 0844 122 947 5_6.do cx @ 23 912 1 @ @ 1
ATTENTION
Always remove the spark plug connector before fitting the bar and starter
cable holder, and when folding the bar out. Following assembly, at the latest
before starting the engine, push the spark plug connector back in place.
Pos: 13.5 /Innente il/Vo rbe reiten de Arbei ten/1.1 Füh ru ngsho lm hoc hste llen ( Abbil dung A1 + B1 + V4 + E1) @ 4 4\mod_1 4696 066 034 19_6. docx @ 5 089 54 @ 2 @ 1

Raise the guide bar (figure A1 + B1 + V4 )

Pos: 13.6 /Innente il/Vo rbe reiten de Arbei ten/Bowde nzüge nic ht kni cken oder e inklemme n WICHT IG @ 44\mod _14 6960 377 3573 _6.do cx @ 50 884 6 @ @ 1
IMPORTANT
Ensure that the Bowden cables are not kinked or trapped when raising the
guide bars!
Pos: null /Innen teil/ Vorbe reite nde Arbei ten/Kabel ni cht k nicken ode r eink lemmen W ICHT IG @ 5 8\mod_ 1567 149 3929 84_ 6.docx @ 604 682 @ @ 1
IMPORTANT
Make sure that the cables are not pinched, squeezed, twisted or overstretched
when the guide bars are folded apart or collapsed! Always run the cables
along the outside of the bar connection. A damaged cable may result in a
technical defect of the device.
Pos: 13.8 /Innente il/Vo rbe reiten de Arbei ten/Führung sholm h ochs telle n Text 52e r Se itena uswu rf_52-PR O S A/52- S A @ 55\mod_ 154 220 7052 518 _6.do cx @ 59 3714 @ @ 1
Open out the Z-shaped, folded guide bar by pulling upwards in the following order:
– First, raise the lower section of the guide bar A1 and firmly tighten the nuts on
both sides B1 .
– Lift the upper guide bar section until upper and lower section of the guide bar
are at one level.
– The quick-release clamps for attachment of the upper and lower section of the
bar are preset by the manufacturer. V4
1. Pull up the quick-release clamp to the bar.
2. Tighten the screws by hand.
3. Open the quick-release clamp.
4. Tighten the screw by 1/4 to 1/2 turn.
5. Pull up the quick-release clamp again and check whether the bars are
firmly connected. Correct if necessary.
– Keep this setting. If the connection becomes loose over time, the screws must
be tightened.
Pos: 13.10 / Innen teil/ Vorbe rei tende Arbe iten/1.1 St ützholm-Mont age (Abb ildu ng W2 + D 1 ) @ 38\mod _14 3824 152 546 4_6.do cx @ 4 0328 7 @ 2 @ 1

Support bar assembly (figure W2 + D1 )

Pos: 13.11 / Innen teil/ Vorbe rei tende Arbe iten/Hol mabst ützung anba uen Text 5 2er Seite nauswu rf ab 2 015 @ 42\mod_ 146 2347 591 409 _6.docx @ 496 402 @ @ 1
– Plug the two screws (1) through the lower section of the bar and place a
washer (2) on each (from the tool bag).
– On the inside of the lower part of the bar, set the support bar (3) to one of the
three positions to set the different bar angles:
• Top notch = steep bar setting (for taller users)
• Bottom notch = flat bar setting (for shorter users)
– Then place a washer (2) on each side and fasten with a nut (4).
– Tighten the two nuts (5) by hand to fix the support bar to the housing.
Pos: 13.12 / Innen teil/ Vorbe rei tende Arbe iten/Hol mhöhenve rs tellu ng...Ums chla gen des Ho lms H inweis 52er Sei tenausw urf ab 2 015 @ 38\mod_ 143 824 6090 956 _6.do cx @ 40 3399 @ @ 1
IMPORTANT
When adjusting the bar height using the support bar, the nuts (2) B1 do not
have to be loosened to fasten the lower part of the bar.
Only loosen the nuts (4) W2 to the extent necessary to allow the bar to move
freely during this task. This prevents the bar from folding over unintentionally
and crush points between the lower part of the bar and the housing are
avoided.
Pos: 13.13 / Innen teil/ Vorbe rei tende Arbe iten/1.1 Ein hängen de s Moto r-Brems- Bowdenzuges am Moto r (Abbil dung H 1 ) @ 3\mod_ 115 2610 373 265 _6.docx @ 174 53 @ 2 @ 1

Attaching the engine-brake Bowden cable to the engine (figure H1 )

Pos: 13.14 / Innen teil/ Vorbe rei tende Arbe iten/Ei nhänge n des Moto r- Brems- Bowden zuges am M otor @ 55\mod _15 4220 759 287 0_6.do cx @ 59 377 0 @ @ 1
– Feed in the angle at the end of the Bowden cable (1) from underneath until the
kink in the brake gear lever (2).
– Pull the movable part of the end of the Bowden cable (3) backwards until the
wire cable (4) can be fed into the recess (5) from the side.
– Then push the Bowden cable (3) forwards until the snap hook (6) clicks into
place in the Bowden cable mounting recess (5).
Pos: 13.15 / Innen teil/ Vorbe rei tende Arbe iten/Ei nhänge n des Moto r- Brems- Bowden zuges Hinwei s neue OB @ 21\mod_ 135 098 2534 155 _6.do cx @ 15 9881 @ @ 1
ATTENTION
After attaching the engine-brake Bowden cable, the brake function of the
safety control bar must be tested. As soon as the control bar is released, the
cutter bar must come to a standstill within three seconds. If this is not the
case, please consult your nearest authorised workshop.
Pos: 13.16 / Innen teil/ Vorbe rei tende Arbe iten/1.1 Holms tart-Montage ( Abbi ldun g L1 ) @ 0\mod_1 1279 863 524 85_6. docx @ 1 414 @ 2 @ 1

Handle starter assembly (figure L1 )

Pos: 13.17 / Innen teil/ Vorbe rei tende Arbe iten/Mon tage Starte rse ilhal ter Text Mo torbrem se @ 37\mod _14 361 9023 917 6_6.do cx @ 3 9970 6 @ @ 1
– Remove the starter cable holder (1) from the tool bag.
– Unscrew the nut until the two halves can be pushed over the bar.
– There is a sticker (2) on the top bar showing the position of the starter cable
holder.
ATTENTION
For reasons of safety, the starter cable holder may only be fitted in the
prescribed position.
– Press the engine stop control bar (3) onto the upper bar section (4) and hold it
there; pull out the starter cable (5) and insert it into the starter cable holder.
– Fit the two halves together (6), re-tighten the nut. This prevents the starter
cable from popping out. The starter cable holder must be fitted / aligned in such
a way that the starter cable is freely accessible and does not rub against any
other parts.
Pos: 13.18 / Innen teil/ Vorbe rei tende Arbe iten/1.1 P ral lblec h anbaue n (Abb ildu ng T1 ) @ 0\mo d_11 152 0086 998 4_6. docx @ 3 29 @ 2 @ 1
6