Maintenance - Ferm 350350 Bedienungsanleitung

ClEl I
( GR )
∆ΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ
∆ηλώουµε υπευθύνωζ τι το προι ν αντο είναι
κατασκευασµένο σύµφωνα µε τονζ εξήζ
Κανονισµούζ ή Κατασκεναστικεζ σνστάσειζ:
IEC1029-2-4, EN61029-1, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
Κατά τιζ διατάξειζ των Κανονισµών τηζ Κοινήζ Αγοράζ:
89/392/EEC
73/23EEC
89/336/EEC
απ 01-07-1999
GENEMUIDEN NL
G.M. Ensing
Quality department
28
- Attach the sanding paper by loosening the but-
ton in the unit (at the top left) and pushing
downwards the spring.
- Stretch the sanding paper as written herunder.
- Close the cover with help of the three screws.
MOUNTING OF THE SANDING PAPER
- Loosen the knurled knob (A) (see fig. 3), but do
not remove it.
- Place the belt on both rolls. Use your left hand
to compress spring (B) so the belt can be placed
easily.
Correct assembly of the sanding belt pre-
vent unnecessary wear. The sanding belt
!
has to be assembled as shown in fig 4. With
your hand you can feel which part of the
sanding belt is on top of the weld.
- Retighten the knurled knob and turn over the
sanding belt a view times with your hands.
- If the sanding belt runs of or runs out of line
then use adjustment screw (C) to adjust the san-
ding belt correctly.
- Put the belt under tension by means of nut (D).
ADJUSTING THE TOOL REST
Disconnect the machine and make sure the
!
sanding belt has stopped before adjusting
the tool rest.
- Loosen nut (E) (see fig. 3) with a spanner.
- Move the tool rest (F) keeping a clearance
between the tool rest and the sanding belt
through which the belt just runs free.
- Retighten nut (E).
- The tool rest can be assembled at two places
depending on the application.

9. MAINTENANCE

While maintaining and cleaning the
machine pull the plug from the mainssoc-
!
ket. Never use water or other agressive
liquids to clean the machine. Clean the
machine by brushing it with a brush.
REGULAR MAINTENANCE OF YOUR MACHI-
NE PREVENTS PROBLEMS:
- Keep the outside of the belt sander/grinder clean
to ensure accurate operation of all moving parts
and prevent excessive wear.
- Replace the grinding stone and sanding belt
when they are worn.
- There is no need to lubricate the transport rol-
lers of the machine.
Ferm Ferm
10. MALFUNCTION
Below we have listed a number of possible causes
and corresponding solutions in case the machine
does not function as it should:
1. The tool does not work when switched on.
Damaged cord and/or plug.
- Check cord and/or plug.
Defective switch.
- Contact your local Ferm dealer to have the switch
inspected and/or repaired.
2. The temperature of the electric motor
exceeds 70°C.
The motor is defective.
- Contact your local Ferm dealer to have the tool
inspected and/or repaired.
I
ClEl
( GB )
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
IEC1029-2-4, EN61029-1, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
in accordance with the regulations.
98/37/EEC,
73/23/EEC,
89/336/EEC
from 26-05-1998
GENEMUIDEN NL
G.M. Ensing
Quality department
5