Storage; Switching Off The Machine; Transport - Kärcher KM 100/120 R Bp Originalbetriebsanleitung

WARNING
Risk of injury due to crushing or shearing off of body parts
when reaching into the mechanics of the waste container!
Do not reach into the movement area or the components of the
emptying mechanism of the waste container.
ATTENTION
Risk of damage when changing the program!
There is a risk of damage if changing the "Drive" program when
the waste container is raised.
Leave the "Drive" program selected while the waste container is
raised. Do not turn the program selection switch to "Sweeping
with roller brush" or "Sweeping with roller brush and side brush".
Note
Using the machine's high dumping, the waste container can be
emptied into e.g. a waste container (for maximum unloading
height, see chapter Technical data).
Raising:
1. Remove all objects that are not securely fastened from the
storage area.
2. Set the program selector switch to "Drive", see chapter Pro-
gram selection switch.
The waste container can only be raised in this position.
Illustration M
Unlock waste container button
1
Button for raising/lowering the waste container
2
Button for opening/closing the container flap
3
3. Position the machine in front of the unloading point.
ATTENTION
Ensure sufficient clearance behind and above the waste contain-
er.
4. Wait at least 1 minute until the dust has settled in the waste
container.
Emptying:
5. Press and hold the "Unlock waste container button".
Note
For safety reasons, the waste container can only be emptied with
two hands. Keep the "Unlock waste container button" pressed
during the entire emptying process.
6. Press and hold the "Button for raising/lowering the waste con-
tainer" in the "Raise" position.
The waste container is raised.
a To empty into a high container, raise the waste container
completely.
Then slowly drive up to the container.
b To empty onto the ground or into low containers, raise the
waste container at least 75 cm.
It is not possible to open the container flap at a lower height.
c Release the "Button for raising/lowering the waste contain-
er".
7. Press the "Button for opening/closing the container flap" to the
"Open" position.
The container flap is opened and the waste container emptied.
8. Press the "Button for opening/closing the container flap" to the
"Close" position.
The container flap is closed.
Lowering:
9. Move the machine approx. 2 m away from the unloading point.
ATTENTION
Ensure sufficient clearance behind and under the waste contain-
er.
10.Press the "Button for raising/lowering the waste container" to
the "Lower" position and lower the waste container completely.
11.Release the "Unlock waste container button" and the "Button
for raising/lowering the waste container".
12.Put the removed objects back on the storage area.

Switching off the machine

ATTENTION
Press the emergency stop switch if a hazardous situation re-
quires the machine and all travel and cleaning functions to be
switched off immediately, see chapter Emergency stop switch.
Do not use the emergency stop switch to switch off the machine
in normal operation, but proceed as follows:
1. Park the machine on a level surface.
Note
The parking brake is automatically activated when the machine is
at a standstill.
Empty the waste container every day before the machine is
switched off for the last time, see chapter Empty the waste con-
tainer.
Charge the battery every day after the last time the machine was
switched off, see chapter Charging the battery.
2. Turn the program selector switch to the "Drive" position.
3. Turn the key in the key switch to position "O" and remove it.
Note
The dust filter is cleaned automatically, then the machine switch-
es off completely.
DANGER
Risk of injury and damage when loading the machine!
When loading the machine, there is a risk of injury from the ma-
chine rolling away, tipping over and falling.
When loading, take into account the weight and dimensions of
the machine and use a suitable ramp.
When loading, secure the machine against rolling away, tipping
over and falling.
Do not use a forklift for loading.
Load the machine only on level, horizontal ground.
On uphill and downhill slopes, move the machine only with the
machine's own travel drive, never by pushing.
DANGER
Risk of injury or damage due to non-observance of the
weight!
Risk of injury and damage due to non-observance of the weight
during transport and storage of the machine.
Be aware of the weight of the machine during transport and stor-
age.
Secure the machine against slipping and tipping during transport
in accordance with the applicable regulations.
1. Load the machine, see chapter Unload the machine.
2. Switch off the machine, see chapter Switching off the ma-
chine.
3. Disconnect the power supply, see chapter Disconnecting/con-
necting the power supply.
4. Secure the machine on the wheels with chocks to prevent it
from rolling away.
5. Tie down the machine with suitable tension belts or ropes at
the marked fixing points.
Illustration N
Shown on a KM 100/120 R G
● Front: On the footrest in the area of the front tower.
● Rear: Openings (ø approx. 30 mm) on the left and right in the
frame between the rear wheels and the waste container.
ATTENTION
The fixing points are marked by chain symbols. Only use the
marked fixing points for lashing, otherwise the machine will be
damaged.
DANGER
Risk of injury or damage due to non-observance of the
weight!
Risk of injury and damage due to non-observance of the weight
during transport and storage of the machine.
English

Transport

Storage

27