Accumulation - Soehnle Professional 6958 Gebrauchsanweisung

6. Operation
Average HOLD:
f
When USER-HOLD-HLD.MOD is set to AVERAG, the hold mode is average hold mode. After entering
this working mode, scale will freeze and display number if scale is stable. If scale is not stable, but
the variation is less than USER-HOLD-DYN.RNG, scale will average data in USER-HOLD-AVG.TIM, then
freeze and display the number. Only the weight that is over USER-OTHER-NLD.RNG can be frozen.
Scale will exit HOLD mode according to the setting of USER-HOLD-HLD.TIM. If the time of scale
variation being over USER-OTHER-NLD.RNG is more than USER-HOLD-STB.TIM, STB.ER will be
shown, press arrow keys to start averaging again, or press HOLD/SETUP key to exit.
Auto HOLD:
f
When USER-HOLD-HLD.MOD is set to AUTO, the hold mode is a auto hold mode. Different subjects can
be weighed one after another without pressing any buttons. After entering this working mode, scale
will freeze and display number if scale is stable. If scale is not stable, but the variation is less than
USER-HOLD-DYN.RNG, scale will average data in USER-HOLD-AVG.TIM, then freeze and display the
number. Only the weight that is over USER-OTHER-NLD.RNG can be frozen. If the held weight is
moved away, and a new load put on the scale, scale will automatically hold new number of load. Scale
will exit HOLD mode according to the setting of USER-HOLD-HLD.TIM. If the time of scale variation
being over USER-OTHER-NLD.RNG is more than USER-HOLD-STB.TIM, STB.ER will be shown, press
[TARE/PRESET] to start averaging again, or press [HOLD/SETUP] key to exit.
In positive or negative Peak HOLD mode, the PEAK and HOLD symbol will be lighted. In another HOLD
f
mode, the HOLD symbol will be lighted. When the HOLD symbol flashes, the displayed number is
active. When the HOLD symbol becomes steady, the displayed number is frozen.

6.6 Accumulation

Accumulation function can be used in normal weighing mode, counting mode and percent weighing mode,
f
When this function is enabled, you can accumulate current net weight, piece, and percentage. Note, only
the load on scale is larger than USER-OTHER-NLD.RNG, the displayed positive number can be added up. The
accumulation times and total can be displayed or printed.
To make data accumulation function be available, CONFIG-FUNC-ACCUMU menu item should set to MANUAL or AUTO.
f
When CONFIG-FUNC-ACCUMU is set to MANUAL, the stable and positive displayed net weight (must be larger
f
than USER-OTHER-NLD.RNG), piece or percentage can be accumulated by long pressing [ACC/TOTAL[ key,
and he terminal will display accumulation times first. Then display total of number. To avoid repeating accu-
mulation for same load, one load only can be accumulated once. So, before a new load put onto the scale,
the original load should be removed and let load on scale be smaller than USER-OTHER-NLD.RNG.
When CONFIG-FUNC-ACCUMU is set to AUTO, the stable and positive displayed net weight (must be larger
f
than USER-OTHER-NLD.RNG), piece or percentage can be accumulated automatically, and indicator will
display accumulation times first, and then display total of number. To avoid repeating accumulation for
same load, one load only can be accumulated once. So, before a new load put onto the scale, the original
load should be removed and let load on scale be smaller than USER-OTHER-NLD.RNG.
To view total, when display number is zero, press [ACC/TOTAL] key long. It will alternatively display the
f
accumulation times and the accumulated sum total thus far (weight or quantity), until the [ACC/TOTAL] key being
pressed again. Note: When HOLD function is enable, and scale is working in PEAK HOLD mode (CON-
FIG-HOLD=YES, USER-HOLD-HLD.MOD=PS.PEAK/NG.PEAK), accumulation function will be automatically disabled!
41