Optional Accessories - Makita BBC231U Betriebsanleitung

Malfunction status
Abnormal vibration:
stop the machine immediately!
Cutting tool and motor cannot stop:
Remove the battery immediately!

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Cutter blade
• Nylon cutting head
• Pole hedge trimmer attachment (for model BBC300L,
BC300LD)
• Pole saw attachment (for model BBC300L, BC300LD)
• Cultivator attachment (for model BBC300L, BC300LD)
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Noise
The typical A-weighted noise level determined according
to ISO22868:
Model BBC231U, BC231UD
Sound pressure level (L
Uncertainty (K): 2.5 dB (A)
The noise level under working may exceed 80 dB (A).
Noise
The typical A-weighted noise level determined according
to EN786:
Model BBC300L, BC300LD
Sound pressure level (L
Uncertainty (K): 2.5 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Vibration
The vibration emission value determined according to
ISO22867, EN786:
Model BBC231U, BC231UD
Vibration emission (a
Uncertainty (K): 1.5 m/s
16
One of nylon cord has been broken
and the head got unbalanced.
The cutter blade is bended, cracked or
worn.
Cutter blade fastening nut is loose.
Cutter blade is fastened improperly.
The drive system does not work
correctly.
Electric or electronic malfunction.
ENG905-1
): 79.7 dB (A)
pA
ENG905-1
): 79.3 dB (A)
pA
ENG904-1
2
): 2.5 m/s or less
h
2
Cause
Vibration
The vibration emission value determined according to
EN786:
Model BBC300L, BC300LD
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Cordless Brushcutter
Model No./ Type: BBC231U, BC231UD
Specifications: see "SPECIFICATIONS" table.
are of series production and
Conforms to the following European Directives:
2000/14/EC, 2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN/ISO11806, EN60335, EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
The conformity assessment procedure required by
Directive 2000/14/EC was in Accordance with annex V.
Action
Bump the nylon cutting head against
the ground while it is rotating to cause
the cord to feed.
Replace the cutter blade.
Tighten the nut properly as described
in this manual.
Ask your local authorized service
center for repair.
Remove the battery and ask your local
authorized service center for repair.
2
): 2.5 m/s or less
h
2
ENG904-1
ENG901-1
ENH035-2