Maintenance - BH FITNESS TR1000BM Montage- Und Gebrauchsanleitung

Should the circuit breaker trip repeatedly then the most
probable causes are:
-Abnormal working conditions,
-Treadmill belt in need of lubricant,
-Solvent based lubricants used (use BH type),
- Belt is too tight.
Plug the unit into a wall socket with an EARTH terminal.
Set switch (L) to Position [1].
ASSEMBLY INSTRUCTIONS.-
Take the unit out of the box and place it on the floor as
shown in Fig.0.
The assistance of a second person is advisable for
the assembly work.
Make sure that all of the pieces are there:
(1) Main structure.
(3) Side bar (left).
(4) Side bar (right).
(18) Tray
(6) Monitor support.
(156) Bottle of lubricant.
(106) Screw M8x20.
(107) Washer D8.5xD20xt1.5.
(117) Screw M6x15.
(62) Nut M8.
(68) Washer D8.
(102) Wire cover.
(108) Screw M3x6.
(118) Screw M5x15.
(119) Nut M8.
(120) Cable clip.
Wrenches.
Follow the instructions step by step to assemble:
1. FITTING THE SIDE BARS.-
At least two people are needed to assemble the machine
This will avoid any possible accidents.
First loosen off screws (105) on the motor cover (14) and
remove the cover (14), Fig.1.
2.
Place the left side bar (3), Fig.2, close to the main
structure and get the wires (TV, internet, LED PCB)
through the left side bar (3), Fig.2. Then slightly screw the
left side bar (3) to the structure using the screws (106) and
washers (107).
3.
Then place the right side bar (4), Fig.2, close to the
main structure and get the power cable, the monitor cable
and the ground cable through the right side bar (4). Then
slightly screw the right side bar (4) to the structure using
the screws (106) and washers (107).
Fig.B
4. ATTACHING THE MONITOR TUBE.-
Take hold of the handrail (18) and connect the cables with
wires sticking up out of the handlebars, Fig.3.
Once this is done, rest the handrail handlebar on top of
the focus bars, making sure not to catch any of the cables.
Now tighten using the nuts (62) and washers (68), Fig.3.
Tighten the screws of the side bars of the previous steps.
5. FITTING THE MOTOR COVER.-
Position the motor cover (14) on the machine, Fig.4, fit
and tighten with the previously removed screws, Fig.4.
6. ATTACHING THE MONITOR.-
Place the monitor support (6) on the tray (18), fix it with
the screws (117) and fasten securely, Fig.5.
Remove the screws from back cover of the monitor and
remove the back cover, Fig.6.
Place the monitor on the support and fix it with the
previously removed screws.
Connect the wires coming out of the monitor with the wires
coming out of the tray. Remove the screws from the back
part of the monitor. Next fix the rear cover using the
previously removed screws, making sure that the wires
are not pressed, Fig.6.
7. WIRE FIXING.-
Attach the fixing support (103) onto the structure using the
screws (104). Use the screws (118) and nuts (119) to fix the
clamp (120), Fig.7.
To fix the connection of the antenna and internet wires use
a screwdriver to open the clamp (120). Insert the wire into
the clamp and tighten the screw again.
8. ATTACHING THE MAINS CABLE
FASTENING COVER.-
First connect the mains cable (51). Then attach the
fastening cover (102) using screws (108), Fig.8.
MOVEMENT & STORAGE.-
The unit is equipped with wheels (46), Fig.9 to make it
easier to move. Make sure that the mains cable is
unplugged from the wall socket.
To prevent accidents DO NOT move the treadmill across
uneven floors.
.

MAINTENANCE.-

Use the bottle of lubricant (156) to lubricate the inside of
the belt Fig.10 in order to keep your unit in top condition
and to ensure that friction between the belt and the board
is kept to a minimum (due to different running styles,
always apply more lubrication to the area where you place
your feet during the exercise).
It is advisable to lubricate the base of the belt between the
board and the band depending on how often it is used.
14