Instructions For Periodic Maintenance - Makita DUC305 Betriebsanleitung

1. R emo v e t h e spro c ket c o v er an d sa w c h ain f rom
t h e tool.
2. R emo v e t h e small d ust or parti c les using a slotte d
s c re w d ri v er w it h a slen d er s h a f t or t h e like.
Fig.37: 1. S lotte d s c re w d ri v er 2. O il d is c h arge h ole
3.
I nsert t h e batter y c artri d ge into t h e tool. P ull t h e
switch trigger to flow built-up dust or particles off the oil
d is c h arge h ole b y d is c h arging c h ain oil.
4. R emo v e t h e batter y c artri d ge f rom t h e tool.
R einstall t h e spro c ket c o v er an d sa w c h ain on t h e tool.
Replacing the sprocket
CAUTION:
A worn sprocket will damage a
new saw chain. Have the sprocket replaced in this
case.

Instructions for periodic maintenance

T o ensure long li f e, pre v ent d amage an d ensure t h e f ull f un c tioning o f t h e sa f et y f eatures, t h e f ollo w ing maintenan c e
must be per f orme d regularl y . W arrant y c laims c an be re c ogni z e d onl y i f t h is w ork is per f orme d regularl y an d prop-
erl y . F ailure to per f orm t h e pres c ribe d maintenan c e w ork c an lea d to a c c i d ents ! T h e user o f t h e c h ain sa w must not
per f orm maintenan c e w ork w h i c h is not d es c ribe d in t h e instru c tion manual. A ll su c h w ork must be c arrie d out b y our
aut h ori z e d ser v i c e c enter.
Check item / Operating time
C h ain saw I nspec tion.
C leaning.
C h ec k at
auth oriz ed
serv ic e c enter.
S aw c h ain I nspec tion.
S h arpening if
nec essary .
G uid e bar I nspec tion.
R emov e f rom
th e c h ain saw .
C h ain brake C h ec k th e
f unc tion.
H av e it
inspec ted
regularly at
auth oriz ed
serv ic e c enter.
C h ain C h ec k th e oil
lubric ation f eed rate.
S w itc h trigger I nspec tion.
L oc k-of f lev er I nspec tion.
O il tank c ap C h ec k
tigh tness.
C h ain c atc h er I nspec tion.
S c rew s and I nspec tion.
nuts
Before Everyday
operation
-
-
- -
-
- -
- -
-
- -
-
-
-
-
- -
- -
17 ENGLISH
Before fitting a new saw chain, check the condition of
t h e spro c ket.
Fig.38: 1. S pro c ket 2. A reas to be w orn out
Always fit a new locking ring when replacing the sprocket.
Fig.39: 1. L o c king ring 2. S pro c ket
NOTICE:
Make sure that the sprocket is installed
as shown in the gure.
Storing the tool
1. C lean th e tool bef ore storing. R emov e any c h ips and
saw d ust f rom th e tool af ter remov ing th e sproc ket c ov er.
2. A f ter c leaning t h e tool, run it un d er no loa d to lubri-
c ate t h e sa w c h ain an d gui d e bar.
3.
C o v er t h e gui d e bar w it h t h e gui d e bar c o v er.
4.
Empt y t h e oil tank.
Every week Every 3
month
- -
- -
- -
- -
- -
- -
- -
- -
-
- -
- -
- -
- -
-
-
Annually Before
storage
- -
- -
- -
-
- -
-
- -
- -
- -
- -
- -
- -
- -
- -