Siemens SINUMERIK 880 Inbetriebnahmeanweisungen Seite 393

9 NC-Maschinendaten/PLC-Maschinendaten/NC-Settingdaten
9.3.5 NC-MD-Beschreibung
1800*
7 6
Anzeigefeinheit
(ab Softwarestand 3)
Wirksam: nach POWER ON
Genaue Beschreibung und Randbedingungen (achsspez. Feinheiten) siehe Kap. 11.7.
Codierug der achsspez. Feinheiten (Eingabefeinheit, Anzeigefeinheit, Lageregelfeinheit)
Bit 7 Bit 6 Bit 5 Bit 4
Bit 7 Bit 6 Bit 5 Bit 4
Bit 3 Bit 2 Bit 1 Bit 0
0 0 0 0
1 0 0 0
0 1 0 0
1 1 0 0
0 0 1 0
1 0 1 0
0 1 1 0
1 1 1 0
0 0 0 1
1 0 0 1
0 1 0 1
1 1 0 1
0 0 1 1
0 0 1 1
0 1 1 1
1 1 1 1
n
9–264
NC-MD
Bit-Nr.
5 4
Eingabefeinheit
Anzeigefeinheit
––––––
-1
10 [mm]
[grad]
-2 -2
10 [mm] 10 [mm]
[grad] [grad]
-3 -3
10 [mm] 10 [mm]
[grad] [grad]
–––––– ––––––
-4 -4
10 [mm] 10 [mm]
[grad] [grad]
10 -5 [mm] 10 -5 [mm]
[grad] [grad]
–––––– ––––––
–––––– ––––––
–––––– -1
10 [grad]
––––––
-2
10 [grad]
-3 -3
10 [mm] 10 [inch]
[grad] [grad]
10 -4 [mm] 10 -4 [inch]
[grad] [grad]
–––––– ––––––
10 -5 [mm] 10 -5 [inch]
[grad] [grad]
––––––
-6
10 [mm]
[grad]
–––––– ––––––
... nicht bei Exportversion
©
Siemens AG 1989 All Rights Reserved
1800*
3 2 1
Lageregelfeinheit
(ab Softwarestand 3)
NC-MD 5002
NC-MD 1800*
Lageregelfeinheit NC-MD 1800*
.
-1 -2
2 10 [grad]
.
-1 -2
2 10 [grad]
.
-1 -2
2 10 [grad]
.
-2
2 10 [grad]
.
-1 -2
2 10 [grad]
.
2 -1 10 -2 [grad]
––––––
––––––
.
-1 -2
2 10 [grad]
.
-1 -2
2 10 [grad]
.
-1 -2
2 10 [grad]
[grad]
.
2 -1 10 -2 [inch]
[grad]
.
-2
2 10 [inch]
.
2 -1 10 -2 [inch]
[grad]
––––––
––––––
SINUMERIK 880, SW1-6 (IA)
11.91
0
Metrisch
(Grad)
Zoll
(Grad)
6ZB5 410-0CP01