Mitsubishi Electric PUMY-P100VHMB Installationshandbuch Seite 10

 (OHFWULFDO ZRUN
L N M1 M2 S M1 M2 S
TB1 TB3 TB7
A B
A : Power source
B : Transmission line
C : Screw on the electrical component box
D : Screw on the electrical component box
)LJ 
 :LULQJ WUDQVPLVVLRQ FDEOHV
1 7\SHV RI FRQWURO FDEOHV
 :LULQJ WUDQVPLVVLRQ FDEOHV
‡ 7\SHV RI WUDQVPLVVLRQ FDEOHV 6KLHOGLQJ ZLUH &996 RU &3(96 RU 0996
‡ &DEOH GLDPHWHU 0RUH WKDQ  PP
‡ 0D[LPXP ZLULQJ OHQJWK :LWKLQ  P
 01(7 5HPRWH FRQWURO FDEOHV
Kind of remote control cable Shielding wire (2-core) CVVS, CPEVS or MVVS
Cable diameter 0.5 to 1.25 mm
:KHQ  P LV H[FHHGHG XVH FDEOH ZLWK WKH
Remarks
VDPH VSHFL¿FDWLRQV DV WUDQVPLVVLRQ OLQH ZLULQJ
([DPSOH RI D JURXS RSHUDWLRQ V\VWHP ZLWK PXOWLSOH RXWGRRU XQLWV 6KLHOGLQJ ZLUHV DQG DGGUHVV VHWWLQJ DUH QHF-
HVVDU\
([DPSOHV RI 7UDQVPLVVLRQ &DEOH :LULQJ!
■ 01(7 5HPRWH &RQWUROOHU )LJ 
■ 0$ 5HPRWH &RQWUROOHU )LJ 
:LULQJ 0HWKRG DQG $GGUHVV 6HWWLQJV!
a. Always use shielded wire when making connections between the outdoor unit (OC) and the indoor unit (IC), as well for all OC-OC, and IC-IC wiring intervals.
b. Use feed wiring to connect terminals M1 and M2 and the ground terminal on the transmission cable terminal block (TB3) of each outdoor unit (OC) to terminals M1, M2
and terminal S on the transmission cable block of the indoor unit (IC).
c. Connect terminals 1 (M1) and 2 (M2) on the transmission cable terminal block of the indoor unit (IC) that has the most recent address within the same group to the terminal
block on the remote controller (RC).
d. Connect together terminals M1, M2 and terminal S on the terminal block for central control (TB7) for the outdoor unit (OC).
H 7KH MXPSHU FRQQHFWRU &1 RQ WKH FRQWURO SDQHO GRHV QRW FKDQJH
Connect shield ground of the indoor units transmission line to the shield (S) terminal of (TB3) and also connect (S) terminal to screw C or D using attached lead wire.
f.
Connect shield ground of the line between outdoor units and the central control system transmission line to the shield (S) terminal of (TB7).
g. Set the address setting switch as follows.
Unit Range
IC (Main) 01 to 50
IC (Sub) 01 to 50
Outdoor Unit 51 to 100
01(7 5& 0DLQ 101 to 150
01(7 5& 6XE 151 to 200
MA R/C
h. The group setting operations among the multiple indoor units is done by the remote controller (RC) after the electrical power has been turned on.
L :KHQ FRQQHFWLQJ D 3:)< XQLW
‡ 'R QRW SHUIRUP WKH JURXS VHWWLQJV IRU WKH 3:)< XQLW DQG WKH LQGRRU XQLWV
‡ 7KH 3:)< XQLW DQG D /RVVQD\ XQLW FDQQRW EH VHW WR RSHUDWH DW WKH VDPH WLPH
‡ 8VH D :0$ UHPRWH FRQWUROOHU IRU WKH 3:)< XQLW
)RU GHWDLOV UHIHU WR WKH LQVWDOODWLRQ PDQXDO IRU WKH 3:)< XQLW
3HUPLVVLEOH /HQJWKV!
1 01(7 5HPRWH FRQWUROOHU
‡ 0D[ OHQJWK YLD RXWGRRU XQLWV //// DQG //// DQG ////
‡ 0D[ WUDQVPLVVLRQ FDEOH OHQJWK / DQG // DQG // DQG / DQG // DQG /
‡ 5HPRWH FRQWUROOHU FDEOH OHQJWK     
,I WKH OHQJWK H[FHHGV  P XVH D  PP VKLHOGHG ZLUH 7KH OHQJWK RI WKLV VHFWLRQ / VKRXOG EH LQFOXGHG LQ WKH FDOFXODWLRQ RI WKH
maximum length and overall length.
2 0$ 5HPRWH FRQWUROOHU
‡ 0D[ OHQJWK YLD RXWGRRU XQLW 01(7 FDEOH //// DQG ////
‡ 0D[ WUDQVPLVVLRQ FDEOH OHQJWK 01(7 FDEOH / DQG // DQG / DQG // DQG /
‡ 5HPRWH FRQWUROOHU FDEOH OHQJWK P DQG PP P DQG PPPP

C
D
2
2
Use the most recent address within the same group of indoor units
Use an address, other than that of the IC (Main) from among the units within the same group of indoor units. This must
be in sequence with the IC (Main)
Use the most recent address of all the indoor units plus 50
* The address automatically becomes "100" if it is set as "01 - 50".
Set at an IC (Main) address within the same group plus 100
Set at an IC (Main) address within the same group plus 150
– 8QQHFHVVDU\ DGGUHVV VHWWLQJ 1HFHVVDU\ PDLQVXE VHWWLQJ
10 m (0.5 to 1.25 mm2)
 &RQWURO ER[ DQG FRQQHFWLQJ SRVLWLRQ RI ZLULQJ
)LJ 
1. Connect the indoor unit transmission line to transmission terminal block (TB3), or
connect the wiring between outdoor units or the wiring with the centralized control
system to the centralized control terminal block (TB7).
:KHQ XVLQJ VKLHOGHG ZLULQJ FRQQHFW VKLHOG JURXQG RI WKH LQGRRU XQLW WUDQVPLVVLRQ
line to the screw (C or D) and connect shield ground of the line between outdoor
units and the central control system transmission line to the shield (S) terminal of
the centralized control terminal block (TB7) shield (S) terminal. In addition, in the
FDVH RI RXWGRRU XQLWV ZKRVH SRZHU VXSSO\ FRQQHFWRU &1 KDV EHHQ UHSODFHG
E\ &1 WKH VKLHOG WHUPLQDO 6 RI WHUPLQDO EORFN 7% RI WKH FHQWUDOL]HG FRQWURO
system should also be connected to the screw C or D using attached lead wire.
2. Conduit mounting plates (ø27) are being provided. Pass the power supply and
transmission wires through the appropriate knock-out holes, then remove the
knock-out piece from the bottom of the terminal box and connect the wires.
3. Fix power source wiring to terminal box by using buffer bushing for tensile force
(PG connection or the like).
3. MA Remote control cables
Kind of remote control cable
Cable diameter
Remarks
* Connected with simple remote controller.
2 :LULQJ H[DPSOHV
‡ &RQWUROOHU QDPH V\PERO DQG DOORZDEOH QXPEHU RI FRQWUROOHUV
1DPH
Outdoor unit controller
Indoor unit controller
Remote controller
Setting Method
500 m (1.25 mm2 or more)
200 m (1.25 mm2 or more)
500 m (1.25 mm2 or more)
200 m (1.25 mm2 or more)
200 m (0.3 to 1.25 mm2)
Sheathed 2-core cable (unshielded) CVV
0.3 to 1.25 mm 2 (0.75 to 1.25 mm
:LWKLQ  P
Symbol Allowable number of controllers
OC –
PUMY-P100  WR  XQLWV SHU  2&
PUMY-P125 1 to 10 units per 1 OC
IC PUMY-P140 1 to 12 units per 1 OC
RC Maximum of 12 controllers
01(7 for 1 OC
RC MA Maximum of 2 per group
2 )*