Installing The Product - Sirius S-DD16 ESSENCE Bedienungsanleitung Mit Montageanweisungen

INSTALLING THE
PRODUCT
1. Before carrying out the appliance installation,
please check that all components are not da-
maged, in such a case contact your retailer
and do not carry out any installation operation.
Furthermore, please read carefully all of the
following installation instructions.
● Use an air exhausting pipe whose maximum
length does not exceed 5 meters.
● Limit the number of elbows in the piping,
since each elbow reduces the air capacity of
1 linear meter. (Ex.: if you use no. 2 x 90 °
elbows, the length of piping should not exceed
3 meters).
● Avoid abrupt direction changes.,
● Use a 150 mm. constant diameter pipe for
the whole length.
● Use piping approved by standards in force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
2. Before making the hole, check that there are
no structural or other parts inside the cabinet,
where the appliance is to be placed, which
could hinder a proper installation.
Check that the dimensions of the product and
the ones of the cook top are compatible with
the cabinet so that the installation can be car-
ried out properly.
3. Make a rectangular opening:
S-DD16 ESSENCE: 832x102 mm
S-DD17 JOLLY: 486X114 mm
in size, in the back of the cook top.
Fit the product in the opening, by inserting it
from above as shown in (Fig. 1).
4. Secure the product inside the furniture by
using the specific brackets provided.
Proceed to the installation of the brackets in
the sides of the product, in the specific hooks,
as shown in fig.2.
Then tighten the screws manually, as in fig.3,
16
EN
to secure the product to the furniture.
Before tightening the screws, make sure that
the product is perfectly balanced. Pay atten-
tion in order not to tighten the screws too
much.
5. If the Downdraft is equipped with external mo-
tor, place the intake unit (external motor) and
settle the exhaust air duct. See the installation
diagram:
with SEM1 or SEM2 Figure 9/10;
with SEM10/12 Figure 10/12;
In case of installation with SEM 1 or SEM 2 it
is recommended to use the fittings and pipes
provided with the kit.
INSTALLATION KIT WITH SDD16 SEM1 OR
SEM2 (See fig. 9).
In case of installation with SEM 1 or SEM 2 it
is recommended to use the fittings and pipes,
included in the installation kit - which is provi-
ded aside.
Then fit the air outlet ducts between the exter-
nal motor and the product. Select the air outlet
among the two available options and fit the
union supplied with the appliance.
S-DD16 ESSENCE: If you intend to use the rear
exit air, you will first have to remove the flange
from product, install the product in the furniture
then restore the flange as shown in fig. 4
6. Place the metal box containing the electronic
components in an easily reachable area for
possible technical assistance operations.
by connecting the related connectors (fig. 5).
7. If the product is equipped with external motor,
connect the motor unit cable to the specific ter-
minal board found the plastic box shown in fig. 6,
8. Power the cookerhood.
9. After completing the installation and connec-
ting the appliance to the power supply, activa-
te the product as indicated in the "HOW THE
COOKER HOOD WORKS" part.
Place the charcoal filters, if the appliance is
used in the recycling mode (charcoal filters
are supplied in a separate kit ), the grease
filters (see fig. 7), and then settle the front
glass by sticking the magnets into the specific
seats.
ESSENCE