Construction; Adjusting; Safety Information - Scheppach CAD115-20Li Original Bedienungsanleitung

period has expired.
• Familiarize yourself with the machine with the help
of the operating instructions manual before using
it.
• Use only original parts for accessories as well as
consumables and spare parts. Spare parts can be
obtained from your scheppach retailer.
• Please quote our article numbers as well as type
and production year in all your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!

6. Construction

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before you
put the cordless equipment into operation:
• Charge the battery pack with the charger. An empty
battery pack requires a charging period of approxi-
mately 0.5 to 1 hour.
Fitting the additional handle (Fig. 3)
• The angle grinder must not be used without the ad-
ditional handle (3).
• The additional handle can be secured in any of
three positions (A, B, C).
Tool side Suitable for
Left (Pos. A) Right-handed users
Right (position B / as Left-handed users
shown)
Top (position C) Using cutting wheels

Adjusting:

• Adjust the guard (1) to protect your hands so that
the material being ground is directed away from
your body.
• The position of the guard (1) can be adjusted to any
specific working conditions. Undo the clamp handle
(c) and turn the cover (1) into the required position.
• Ensure that the guard (1) correctly covers the gear
wheel casing.
• Secure the clamp handle (c) again.
• Ensure that the guard (1) is secure.
m Take care that the safety device is secure.
m Never use the angle grinder without the guard.
Test run for new grinding Wheels
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Allow the right-angle grinder to run in idle for at least
1 minute with the grinding or cutting wheel fitted in
place. Vibrating wheels are to be replaced immedi-
ately.

7. Safety information

m WARNING Read all safety warnings and all in-
structions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Opera-
tions:
1. This power tool is intended to function as a grind-
er, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool. Fail-
ure to follow all instructions listed below may re-
sult in electric shock, fire and/or serious injury.
2. Operations such as polishing are not recommend-
ed to be performed with this power tool. Opera-
tions for which the power tool was not designed
may create a hazard and cause personal injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool manu-
facturer. Just because the accessory can be at-
tached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the pow-
er tool. Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6. Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbour hole of the acces-
sory must fit the locating diameter of the flange.
Accessories that do not match the mounting hard-
ware of the power tool will run out of balance, vi-
brate excessively and may cause loss of control.
7. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for loose
or cracked wires. If power tool or accessory is
dropped, inspect for damage or install an undam-
aged accessory. After inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run
the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
8. Wear personal protective equipment. Depending
19 | GB