Introduction; Device Description; Technical Data; Scope Of Delivery - Scheppach CAD115-20Li Original Bedienungsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
we wish you a pleasant and successful working ex-
perience with your new scheppach machine.
Note:
According to the applicable product liability law the
manufacturer of this device is not liable for damages
which arise on or in connection with this device in
case of:
• improper handling,
• non-compliance with the instructions for use,
• repairs by third party, non authorized skilled work-
ers,
• installation and replacement of non-original spare
parts,
• improper use,
• failures of the electrical system due to the
non-compliance with the electrical specifications
and the VDE 0100, DIN 57113 / VDE 0113 regu-
lations
Recommendations:
Read the entire text of the operating instructions pri-
or to the assembly and operation of the device.
These operating instructions are intended to make it
easier for you to get familiar with your device and uti-
lize its intended possibilities of use.
The operating instructions contain important notes
on how to work safely, properly and economically
with your machine and how to avoid dangers, save
repair costs, reduce downtime, and increase the reli-
ability and working life of the machine.
In addition to the safety regulations contained herein,
you must in any case comply with the applicable reg-
ulations of your country with respect to the operation
of the machine.
Put the operating instructions in a clear plastic fold-
er to protect them from dirt and humidity, and store
them near the machine. The instructions must be
read and carefully observed by each operator prior
to starting the work. Only persons who have been
trained in the use of the machine and have been in-
formed on the related dangers and risks are allowed
to use the machine. The required minimum age must
be met.
In addition to the safety notes contained in the pres-
ent operating instructions and the special regulations
of your country, the generally recognized technical
rules for the operation of wood working machines
must be observed.
18 | GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.
2. Device description (Fig. 1, 2)
1. Protective device
2. Spindle locking
3. Safety switch
4. On/off switch
5. Face spanner
6. Additional handle

3. Technical data

Motor power supply:
Rated speed:
Max. wheel diameter:
Bore diameter:
Mounting spindle thread:
Subject to technical changes!
Noise and vibration
m Warning: Noise at the workplace can exceed 85
dB (A). In this case, noise protection measures are
necessary for the user (wear hearing protection!).
Noise output in dB
sound power level L 89,5 dB(A) (EN ISO 3744)
WA
sound pressure level L 78,5dB(A) (EN ISO 11201)
pA
uncertainty K 3 dB(A)
wa/pA
Vibration value
Vibration a 7,54 m/s²
h
Uncertainty K 1,5 m/s²
h

4. Scope of delivery

• Cordless Angle Grinder
• Additional handle
• Face spanner
• Translation of original instruction manual

5. Unpacking

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage. Inform the transport agent imme-
diately of any faults. Later complaints cannot be
considered.
• If possible, store the packaging until the warranty
20 V
8000 min-1
ø 115 mm
22 mm
M14