Troubleshooting Guide; Warranty; Technical Data; Eu Declaration Of Conformity - Kärcher LTR 18-30 Battery Originalbetriebsanleitung

Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device does not start
up
The device does not start
up
The device does not start
up
The device stops during
operation
The device stops during
operation
The device stops during
operation
The device stops during
operation
The device stops during
operation

Warranty

The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Technical data

Device performance data
Working voltage of the battery
Working width
Cutting string, diameter
Idle speed
Determined values in acc. with EN 50636–2-91
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L + K uncer-
WA
tainty
WA
Front handle hand-arm vibration
value
Rear handle hand-arm vibration
value
Uncertainty K
Dimensions and weights
Length x width x height
Weight (without battery pack)
Subject to technical modifications.
22

Troubleshooting guide

Cause
Battery pack is not inserted correctly.
Battery pack is empty
Battery pack is defective.
String is too long and is causing the mo-
tor to overload
Cutting head blocked by cutting residue  Remove the cutting residue.
Motor is overloaded
Motor has overheated
The battery has overheated
V 18
mm 300
mm 1,65
1/min 7700 +/-
10%
dB(A) 85,8
dB(A) 2,5
dB(A) 96
2
m/s 1,4
2
m/s 0,6
2
m/s 1,5
mm 1329 x 3
12 x 327
kg 2,2
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
 Push the battery pack into the mounting
until it latches into place.
 Charge the battery pack.
 Replace the battery pack.
 Install the string guard.
The string will automatically be shortened.
 Mow only suitable cutting material, see
Chapter Intended use.
 Stop working and allow the motor to cool
down.
 Stop working and allow the battery to cool
down to normal battery temperature.

EU Declaration of Conformity

We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
Product: Lawn trimmer/edge trimmer
Type: LTR 18-30 Battery 1.444-31x.0
Currently applicable EU Directives
2000/14/EC (+2005/88/EC)
2006/42/EC (+2009/127/EC)
2011/65/EU
2014/30/EU
Harmonised standards used
EN 60335-1:2012+A11:2014+A13:2017
EN 50636-2-91:2014
EN 50581:2012
EN 55014-1:2017
EN 55014-2:2015
Conformity evaluation procedure used
2000/14/EC and amended by 2005/88/EC: Annex VI
Sound power level dB(A)
Measured:93,2
Guaranteed:96
Name and address of the notified body involved
Société Nationale de Certification et d'Homologation
2a. Kalchesbruck
L-1852 Luxembourg
ID no. 0499
The signatories act on behalf of and with the authority of
the company management.
H. Jenner
Chairman of the Board of Management
English
S. Reiser
Director Regulatory Affairs & Certification