Ryobi RBC30SESC Bedienungsanleitung Seite 25

comfort.
■ Tighten the bolts securely.
RBC30SESC
■ Remove the securing bolts and bracket from the front
handle.
■ Align the hook into upper shaft slot.
■ Install the front handle onto the upper shaft.
NOTE: The front handle should tilt slightly towards the
operator when correctly fi tted.
■ Place the securing bolts through the front handle and
securely tighten them into the captive nuts on the
bracket.
NOTE: Do not attempt to remove the hook on the
bracket, the hook limit the upper position of the front
handle.
ATTACHING THE BLADE GUARD AND GRASS
DEFLECTOR
Blade guard
(Fig. 2b)
■ To attach the blade guard to the mounting bracket,
align the screw holes on the blade guard to the bolts
on the mounting bracket.
■ Use the combination wrench to tighten the bolts
securely.
WARNING:
– The blade guard should remain fitted to the product
at all times.
– When using the line trimmer bump head, the grass
deflector must be attached to the blade guard.
– When using the brushcutter blade, the grass
deflector must be removed from the blade guard.
Grass defl ector
(Fig. 2b)
■ To attach the grass deflector to the blade guard, align
the 3 screws on the grass deflector to the screw holes
on the blade guard.
■ Use the combination wrench to tighten the bolts
securely.
NOTE: When using the line trimmer bump head, the
grass defl ector must be attached to the blade guard.
ATTACHING THE POWER HEAD TO THE TRIMMER
ATTACHMENT (Fig 2c)
WARNING: Never attach or adjust any attachment while
power head is running. Failure to stop the engine may
cause serious personal injury.
■ The trimmer attachment connects to the power head
English (Original instructions)
■ Loosen the knob on the coupler of the power head
■ Push in the button located on the trimmer attachment
■ Align the button with the guide recess on the power
■ Rotate the trimmer attachment shaft until the button
■ Tighten the knob securely.
REMOVING THE ATTACHMENT FROM THE POWER
HEAD
■ Loosen the knob.
■ Push in the button and twist the shafts to remove and
INSTALLING THE REELEASY™ LINE TRIMMER HEAD
(Fig. 2d)
■ Stop the engine and disconnect the spark plug wire.
■ Open the ReelEasy™ Line Trimmer Head by
■ Remove the line trimmer head cover, bump knob, and
■ Place the cutting head housing on the drive shaft.
■ Make sure the housing is fully seated.
■ Install the hex bolt to secure the line trimmer head to
■ Tighten by using the hex-shaped opening on the
■ Reinstall the bump head spring into the line trimmer
■ Reinstall the line spool.
■ For the straight shaft attachment with the ReelEasy
■ Replace the bump knob by inserting it into the centre
23
by means of a coupler device.
shaft and remove the end cap from the attachment.
shaft.
head coupler and slide the two shafts together.
locks into the positioning hole.
NOTE: If the button does not release completely in
the positioning hole, the shafts are not locked into
place. Slightly rotate from side to side until the button
is locked into place.
separate the ends.
depressing the latches on each side.
NOTE: The contents of the line trimmer head are
spring loaded, so keep your other hand over the line
trimmer head cover while depressing the latches.
line spool and set aside.
the drive shaft.
inside of the bump knob.
NOTE: Only use the bump knob to tighten the bolt.
The use of other tools may allow over tightening of the
bolt, which could damage the line trimmer head.
head and push down to seat.
cutting head the spool should be placed so "This side
out for straight shaft" is visible on the line spool.
of the line spool.
TM