Herunterladen Inhalt Inhalt Diese Seite drucken

Cleaning Hard Floors - Polti Unico MCV85 TOTALCLEAN & TURBO Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für Unico MCV85 TOTALCLEAN & TURBO:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 79
6.3 In pre-set-program mode, it is possible to activate suction
by pressing the suction button (3).
To stop the program being used, press and quickly release the
steam delivery button.
To restart the program press the steam delivery button for at
least one second.
To deactivate the program press the PROGRAM button
repeatedly until the indicator light goes off.

7. CLEANING HARD FLOORS

(tiles, ceramic surfaces, stoneware, ...)
SUCTION ONLY FUNCTION
7.1 For suction alone, set the Multibrush brush to position C
(bristle inserts) pressing the pedal (which ensures that the
holder with cloth is not attached to the brush).
For safety reasons, apply the steam lock on the handle during
vacuuming.
Make sure that Chapter 1 has been carried out and begin the
cleaning operations.
It is possible to adjust the suction power by moving the cursor
on the handle (4).
STEAM ONLY FUNCTION
To clean using steam alone, it is possible to use the abrasive
action of the cloths supplied, attaching them to the special
holder (18). Position the holder with the cloth on the floor and
position the multibrush above it in position A (no insert), apply
slight pressure until it clicks, locking into place (19).
Make sure that Chapter 2 has been carried out and begin the
cleaning operations.
It is possible to adjust the intensity of the steam by using the +/-
buttons (see Chapter 4); for this type of surface we recommend
the maximum level of steam.
Before removing the holder with cloth from the brush, wait a
few minutes to allow the cloth to cool. Never use the holder
without a cloth.
STEAM - VACUUM COMBINED FUNCTION
to sanitise and dry the surface
For steam cleaning and suction, set the Multibrush in position B
(rubber inserts) and ensure that the holder with cloth is not
attached to the brush. Make sure that Chapters 1 and 2 have been
performed and proceed with the cleaning operations: first by
steaming and then vacuuming to dry.
It is possible to adjust the intensity of the steam by using the +/-
buttons (see Chapter 4); for this type of surface we recommend
the maximum level of steam.
It is possible to adjust the suction power by moving the cursor
on the handle.
The combined use of steam and suction allows the most
efficient sanitising of the surface, dissolving dirt, eliminating
grease, germs and mites, and above all makes it possible to
remove excess humidity and reduce the cleaning operations
time.
PROGRAMMED MODE
For this type of surface there is a pre-set cleaning program, see
Chapter 6.
To avoid any dirt in the dirt collector causing bad smells
(especially where liquids and/or steam humidity are
vacuumed), we recommend emptying and cleaning after every
use according to the methods described in Chapter 17.
8. CLEANING DELICATE FLOORS
(wooden, stone, waxed surfaces, etc.)
Before using the appliance on delicate surfaces, ensure that
the part in contact with the surface is free from foreign bodies
that could cause scratches.
SUCTION ONLY FUNCTION
For suction alone, set the Multibrush to position C (bristle
inserts) pressing the pedal (make sure that the holder with cloth
is not attached to the brush).
For safety reasons, apply the steam lock on the handle during
vacuuming.
Make sure that Chapter 1 has been carried out and begin the
cleaning operations.
It is possible to adjust the suction power by moving the cursor
on the handle (4).
STEAM ONLY FUNCTION
For cleaning only with steam, set the Multibrush to position A
(no insert). Attach the cloth supplied to the relative holder;
place the holder with cloth on the ground and position the
brush above, applying slight pressure until a click is heard as it
locks into place (19).
Make sure that Chapter 2 has been carried out and begin the
cleaning operations.
It is possible to adjust the intensity of the steam by using the +/-
buttons (see Chapter 4); for this type of surface we recommend
the minimum level of steam.
Before removing the holder with cloth from the brush, wait a
few minutes to allow the cloth to cool. Never use the holder
without a cloth.
STEAM - VACUUM COMBINED FUNCTION
to sanitise and dry the surface
For cleaning with steam and suction, set the Multibrush to
position A (no insert). Attach the cloth supplied to the relative
holder (18); place the holder with cloth on the ground and
position the brush above, applying slight pressure until a click
is heard as it locks into place (19).
| 34 |

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Unico mcv80 totalclean & turbo

Inhaltsverzeichnis