GYS EXAGON 400 CC/CV Bedienungsanleitung Seite 20

SEMI-AUTOMATIC MIG / MAG WELDING WITH WIRE FEEDER (EXAFEED
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the positive (+) or negative (-) terminal depending on the wire type
• Connect the connection cable on the remaining power connector,
• Plug the connection cable's command connector on the 10 points base situated between the two power connectors (FIG-1, n°5),
• Refer to the wire feeder's user manual for the remaining connections.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
Both display show - - - and the knobs are inactive, all controls are now opera-
ted from the wire feeder's interface (Refer to the wire feeder's user manual for
the control settings).
SEMI-AUTOMATIC MIG / MAG WELDING WITH VOLTAGE DETECTING WIRE FEEDER (
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the positive (+) or negative (-) terminal depending on the wire type
• Connect the wire feeder on the connector using a male-female cable (NOMAD CABLE),
• Refer to the wire feeder's user manual for the remaining connections.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
1. Setting the welding voltage :
Adjust the welding voltage using the main knob
to be carried out. The voltage setpoint is indicated on the left side display.
2. Inductance settings :
Adjust the inductance level using the second knob
-9 to +9. The lower the inductance level, the harder and more guiding the arc.
The higher the inductance and the softer the arc with little splatter.
CARBON ARC GOUGING
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the negative (-) terminal
• Connect the gouging torch on the positive (+) terminal
• Orient the clamp depending on the working position, make sure that the compressed air flows in the arc's direction and not the other way around.
• Place a carbon electrode,
• Connect the compressed air to the gouging torch,
The arc strike is easier : just make contact with the piece, and advance while pushing the electrodes towards the metal to be removed.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
Adjust the arc voltage using the main knob
cated on the left side display.
• 36V to 45V for a 6.35 mm electrode.
• 39V to 45V for a 8 mm electrode.
DISPLAY CURRENT/VOLTAGE DURING WELDING
During welding, the machine measures and displays the welding current and voltage. After the weld, the average current and voltage values are
displayed during 30 seconds, as soon as a knob or a button is pressed, the welding parameters are displayed.
20
EXAGON 400 CC/CV
depending on the work
, a relative value from
, the voltage setpoint is is indi-
)
,
(in general on the -)
VRD
V A
0
ARC FORCE
INDUCTANCE
-9 +9
The grey areas are not useful for this mode.
,
(in general on the -)
VRD
V A
0
ARC FORCE
INDUCTANCE
-9 +9
The grey areas are not useful for this mode.
VRD
V A
0
ARC FORCE
INDUCTANCE
-9 +9
The grey areas are not useful for this mode.
EN
M A D E I N F R A N C E
MMA MIG TIG Gouging
press 3 s
Basic
7018
CV
Rutile
6013
MODE
Cellulosic
6010
press 3s press 3s
setup
memory
)
M A D E I N F R A N C E
MMA MIG TIG Gouging
press 3 s
Basic
7018
CV
Rutile
6013
MODE
Cellulosic
6010
press 3s press 3s
setup
memory
M A D E I N F R A N C E
MMA MIG TIG Gouging
press 3 s
Basic
7018
CV
Rutile
6013
MODE
Cellulosic
6010
press 3s press 3s
setup
memory