Program Sorting By Name Or Program Number; Change Standard Drying Position And Steps; Change Tempering Positions; Display Date Or Time - DENTSPLY Multimat 2 Touch Gebrauchsanweisung

01. Boot PC / Laptop
02. Open the Windows Explorer
(Start/Programs/Windows Explorer).
03. Insert floppy disc or CD-ROM containing the new software.
04. Click on 3.5" Disc (A:) or CD-ROM.
05. On the right hand side of this window you should see
a file called MMT_Updt.exe, which has a satellite dish as
a symbol.
06. Click on this file.
07. Choose your language from the options shown.
08. Disconnect the furnace from the mains supply
(pull out the plug).
09. Re-connect the furnace to the mains supply
(put the plug back in the socket).
10. The computer will now start with the data transfer
(approx. 2 – 3 minutes). The update is finished when
"Ready!" appears in the dialogue window of your furnace.
11. Disconnect the power cable and the serial cable from the
furnace. Wait for 5 seconds, and then reconnect only the
power cable.
12. The Multimat2 Touch display now shows the latest soft-
ware version on the start screen.

6.12 Program sorting by name or program number

(Main menu, section 4.5.1)
This function is used to sort programs by name or program
number. As a helpful feature, programs are given a letter prefix
for sorting alphabetically.
Program sorting
1. Press sensor button "M".
2. Press sensor button "Configuration".
3. Press sensor button "Sorting" and select by name or
number.
4. Press sensor button "M" until the previous program is
displayed.
Note: This function can only be used with Latin characters.

6.13 Change standard drying position and steps

This function can be used to change the standard drying posi-
tion and the number of steps after which the standard drying
position is reached, measured from the upper end position.
Set new drying position
1. Press the text field "Drying" (not the sensor button!)
twice. A selection screen is displayed.
2. Press the sensor button "Drying position".
3. Enter the new drying position in "mm" with the numeric
sensor keypad.
4. If the drying position is lower than 100 mm, press the sensor
button "Drying position" again.
Note: The drying position can be adjusted between 0 and
150 mm. 0 mm is the starting position in the selection screen.
Adjust drying steps
1. Press the sensor button "Steps".
2. Enter number of steps with the numeric keypad.
3. Press "Arrow left", and the program is displayed again.
Note: To permanently store the changed drying parameters,
the program must be saved before the start. The new drying
parameters apply only for the changed program. All other
programs remain unaffected.
Caution! We recommend not changing the default standard
drying positions and steps without urgent reasons.

6.14 Change tempering positions

This function can be used to change the tempering position.
Set new tempering position
1. Press the text field "Tempering" in the program twice.
A selection screen is displayed.
2. Press sensor button "Tempering position".
3. Enter the new tempering position in "mm" with the numeric
sensor keypad.
4. If the tempering position is lower than 100 mm, press the
sensor button "Tempering position" again.
5. Press "Arrow left", and the program is displayed again.
Note: To permanently store the changed tempering position,
the program must be saved before the start. The new tempering
position applies only for the changed program. All other programs
remain unaffected.
Change the tempering positions for
ceramics only after consultation with the
manufacturer.

6.15 Display date or time

This function is used to set either the date or the time to be
displayed in the program. The factory setting is the date.
Changing the time or date display
1. Press the sensor button "Drying position".
2. Press the sensor button "Configuration".
3. Press the sensor button "Display date" or "Display time".
The display changes to date or time.
4. Touch sensor button "M" until the previous program is
displayed.
59